-
MMSD replied to the thread John Deere 435 tractor.Injectors for that one are not that expensive. The blower is a big deal to get done right if it was never upgraded.
-
MMSD replied to the thread Clutch stuck jd 420.Sounds like the pilot bearing in the clutch locked up and won't let the clutch stop spinning. #23 in the picture.
-
-
MMSD replied to the thread Parade/show tractor tire dressing.I like the Lucas "Slick Mist Tire and Trim Shine". Just mist it on and rub it in. Leaves a nice none gloss look to them and seems to...
-
MMSD replied to the thread oliver 70 engine.Justin Dodge from IA is the Oliver guy to talk to. He builds some pretty tough stuff.
-
MI have pulled and attended the NATPA in Ohio and I witnessed some impressive Oliver tractors . Where I met the amazing Mel ,get know and...
-
MMSD replied to the thread Levanna Road news.Propane was priced the same as we paid last year here in SE SD.
-
MMSD replied to the thread Noisey Gears.Could be anything in the tranny then. Bearing rusted up or worn out most likely.
-
MMSD replied to the thread Noisey Gears.Did it make that noise before you worked on it or is it just new since then?
-
MMSD replied to the thread Correct John Deere Black for a 444C.John Deere has a Blitz Black that is a pretty good color. Don't know if it is correct for what you are doing but it is a nice shade.
-
MMSD replied to the thread John Deere 1020 losing fluid.Hydraulic fluid leak by the 3 point shaft by the hitch is common on them. I've replaced seals with the proper size o rings with pretty...
-
MMSD replied to the thread 2155 brake bleed problem.Don't know if it has anything to do with the brakes not bleeding but did you clean the screen under the transmission case? They get...
-
MMSD replied to the thread Am I being misled?.Looks like they didn't have them loose enough when they took them off the crank. You can see the spline marks on them .
-
MMSD replied to the thread Pulling a 706 Diesel questions?.Heard that a 1/2" is like a 400 lb difference. Don't know if it is true or not.
-
MMSD replied to the thread Pulling a 706 Diesel questions?.Problem is with your design there is no adjustability in it. Not only for going from 18 to 20 inch height but also how you place your...
-
MMSD replied to the thread Pulling a 706 Diesel questions?.Do you have adjustable bolts under the hook paddle to hold it at the set height? Around here there is no set minimum height but there is...
-
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy