(800) 853-2651
SHOP NOW

Recent content by NatWester

Yesterday's Tractor Forums
  1. N

    Long 610 - Engine Knock

    I pulled off a main cap today.... not the prettiest but idk if it's bad enough to cause the knocking. It looks like it's been like that for awhile
  2. N

    Long 610 - torque specs

    Long 610 4 cylinder 102mm D-121.050 What are the Main Bearing Caps & Connecting Rod Caps Torque Specs?
  3. N

    Long 610 - Engine Knock

    Yes, plastigage: all 4 were 0.0015-0.002 No, I didn't take out the crank or do mains Rod bearings were std Yes, I lined up holes Oil? I used Vaseline Yes, plastigage: all 4 were 0.0015-0.002'' No, I didn't take out the crank or do mains All the rod bearings were std, old & new Yes, I lined up...
  4. N

    Long 610 - Engine Knock

    Long 610 4 cylinder 102mm. Full engine rebuild: new pistons/rings, cylinders honed, new rod bearings, and a complete gasket set. Before the rebuild, I had the injection pump and all the injectors rebuilt. But it sounds like it's knocking, and it gets worse when rpms go up. It's not the valves...
  5. N

    Long 610 injector pump timing

    I moved it 1 tooth.... 🤔 Oil pressure is almost 50psi @1500 rpm
  6. N

    Long 610 injector pump timing

    Does this look right?
  7. N

    Long 610

    Long 610 4 cylinder - injector pump timing? I had the injection pump and all the injectors rebuilt, engine has been rebuilt - new pistons/rings, cylinders honed, new rod bearings, and a complete gasket set- but I've got a rattle/knock that gets worse when rpms go up Note: at idle, oil pressure...
  8. N

    Injection pump timing

    Long 610 4 cylinder 102mm D-121.050 injection pump: which way to twist it to advance the timing? top towards the engine? Because I think mine's too far advanced, hence the rattle as rpms go up
  9. N

    Long 610

    Valve clearance - is .010 too tight?
  10. N

    Long 610

    Long 610 -fresh rebuild: pistons, rings, honed, rod bearings, gasket kit Good oil pressure 50psi, but.... It has a rattle, gets worse at higher rpm
  11. N

    Long 610

    Long 610 -fresh rebuild: pistons, rings, honed, rod bearings, gasket kit Good oil pressure 50psi, but.... It has a rattle, gets worse at higher rpm
  12. N

    Long 610 - 1st oil change?

    Long 610 4 cylinder 102mm - fresh rebuild: pistons, rings, honed, rod bearings, gasket kit. Break-in: how soon should i change the oil?
  13. N

    Long 610 - Air Filter

    Air filter assembly, removed, bottom view. I've got the cup and the lower filter element removed. I'd like to take it apart and pressure wash the whole thing. How can I clean this upper element? Diesel/pressure wash? The inside of the center tube is cake with dirt/dust
  14. N

    Long 610

    Long 610 connecting rod bearing - URB 11503177 R0 - are these std? The rod journal is 2.313''
  15. N

    Long 610

    Long 610 update: It was hard to start, had LOTS of blow-by. I got it apart.... busted ring lands on the pistons, cylinders were.... ok. I got new pistons, rings, rod bearings, and a complete gasket set. I've got the heads surfaced and cleaned up. I honed the cylinders and surfaced the block My...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top