(800) 853-2651
SHOP NOW

Recent content by pixer

Yesterday's Tractor Forums
  1. P

    Plans for lift to attach to an 8n 3 point hitch

    Yes that?s exactly what I had in mind my e mail is [email protected] . is the pipe normal black iron pipe or a thick wall type?.
  2. P

    Plans for lift to attach to an 8n 3 point hitch

    Does anyone have plans to build a hoist or lift for a 3 point hitch maybe using pipe for the main boom I could use angles and measurements.. I put my email in when posting so if plans can be sent via e mail great, otherwisee I can copy plans off of post. . Thanks in advance
  3. P

    Proper implement hookup

    Well Tim you took me to school,I?m not a new you in one sense having owned 3 n,s I have run them in paradesand tractor runs but I am a newbie in the farming aspect. As far as left or right over drivers side passenger side, you don?t have to explain looking T the tractor from front or back ,it...
  4. P

    Proper implement hookup

    I can keep my 8n in good running condition but never having farme I don?t know how to properly hook up implements. I have my 6ftrear blade on and have the top link hooked to the pin that?s attached to the large spring. I believe that?s ok . Under this pin their are two places to attach things...
  5. P

    Early 8n steering box overhaul

    If I buy a steering box overhaul kit for my 47 8n 4 bolt steering box and replace all parts that come with it will it take out the excessive play my steering has in it?. I have tried turning the tight sector clockwise and turning left sector the opposite, this only made it harder to the wheel...
  6. P

    2007 ford f150

    Not coolant smell, smells like engine smell canengine air get to vent inlets? I think their in the grids right under the wiper blades, could the smell come between the hood and the hood rubber seal ?
  7. P

    2007 ford f150

    I need a ford guy for a question, my pickup has no discernible exhaust leaked yet when I run the heater or air conditioner with the vent open I get motor smell in the cab anyone know how it could get in the cab? And how do I stop it. There's a lot of knowledge on this thread so I'm giving the...
    • pixer
    • Thread
    • Replies: 5
    • Forum: Ford
  8. P

    Warning

    Your probably right rouse the nut holding it on was so far in the cotter pin barely met the grooves in the nut,but getting the seal out wasn't bad, I just wanted to warn that this may happen.
  9. P

    Front wheel bearing replacement

    Your right Gary I put nut back after removing washer and outer bring and yanked and ruined the bring don't do it
  10. P

    Warning

    I recently read on a blog that in changing an 8n front seal it said remove nut washer and front bearing then put nut on and yank to remove seal.i did that and ruined the inner bearing it seperated the inner bearing in 3 pieces . I.e. It knocked it apart.beware.
  11. P

    Front wheel bearing replacement

    I plan on replacing both races that come with the bearing kit.What is the name of the part that goes on the spindle first, it is tapered and slides on the spindle and seat against the spindle itself. This part must be intended to be reused because u couldn't find it in any catalogue and the...
  12. P

    Front wheel bearing replacement

    Decided to replace front wheel bearing seal on 47 8n, pulled off hub and inner bearing came off in pieces, ordered bearing kit and started to remove races and noticed there are two indentations in hub across from each other ,is this where you get the punch on the back of the races to drive...
  13. P

    Setting points and timing

    Late getting back to read, starting to get the idea about setting timing appreciate the information
  14. P

    Setting points and timing

    Have 47 early 8n, read about how to change points, am I right in saying you set point gap at 015 and that is step one , then you use a steel Ruler to set the timing?. This part ils a little tricky it reads like. But do you always need to reset the timing after changing points.?
  15. P

    Another new project 2027

    Great pics and educational to we need more of this
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top