(800) 853-2651
SHOP NOW

Recent content by Pknapp

Yesterday's Tractor Forums
  1. P

    NAA fel hydraulics for log splitter

    My fear is that it will be too slow. The FEL does move quite fast so maybe it will be ok.
  2. P

    NAA fel hydraulics for log splitter

    I have an NAA with a wagner front end loader with a front driven pump. The previous owner installed a valve and external lines to run a 3 pt back hoe. I was wondering if this set up would work to power a 3 pt log splitter? Thanks, Pete
    • Pknapp
    • Thread
    • Replies: 5
    • Forum: Ford
  3. P

    jd rotary mower clutch stuck

    Tried tapping on them but they are rusted solid
  4. P

    jd rotary mower clutch stuck

    Bought a JD 509 cutter and the manual says to loosen the clutch adjusting nut and free up the clutch. I loosend the nut but the clutch plates are rusted fast. Any ideas on freeing the plates up?
  5. P

    sherman transmission

    Maybe this will help http://forums.yesterdaystractors.com/ttforum/viewtopic.php?t=757215&sid=5db3b3b2d2a600cba5067f52c6b30036
  6. P

    JD 509 mower any good?

    Thanks for the information. Drove 140 miles round trip to pick up a really nice 509.
  7. P

    JD 509 mower any good?

    Wondering if anyone has info on this mower. From the little I have found online it seems to be a heavy duty mower. Not much info though. Is $750 a reasonable price in decent condition?
  8. P

    jd 503 mower pto shaft question

    I am looking at a used JD 503 rotary mower but it comes with out the shaft. Traded at a local dealer, owner kept the shaft. I need to know the shaft length and if a round bore with a shear pin is acceptable to use on the 6 spline mower input shaft. I know a clutch is better but I am trying to...
  9. P

    3 point tiller

    I just bought a jubilee that has a howard low speed transmission in it. The forums say that this is the only setup to till with a jubilee. Now I want a tiller to go with the Howard. Man is this thing slow with it in low gear.
  10. P

    lift pin replacement advice

    Correction. The old pins were 5/8 fine, the new ones are 3/4" fine thread.
  11. P

    lift pin replacement advice

    If you buy new lift pins, best to buy the nuts and flat washers as well. I found out the hard way tonight when my new pins arrived and the old castle nuts and washers were too small. Be nice if the ad mentioned that they changed the nuts size to 5/8".
    • Pknapp
    • Thread
    • Replies: 1
    • Forum: Ford
  12. P

    lift support pin leaking

    Just need to remove the last couple nuts and the trumpet will be out. Hopefully tomorrow nights job. This tractor has a howard tranny. Just wondering if this complicates the removal? Thanks.
  13. P

    lift support pin leaking

    It is on a 1953 NAA. Ordered the parts from the marketplace last night. Seems like an easy fix. The loader will be a bit in the way though.
  14. P

    lift support pin leaking

    my right lift support pin is loose and seeping oil. How big a job is it to remove the axle housing and replace the pin?
    • Pknapp
    • Thread
    • Replies: 5
    • Forum: Ford
  15. P

    NAA distributor parts

    I just picked up a 1953 NAA with Wagner FEL,Sherman overdrive,and Howard transmission. In the process of tuning it up I found excessive play in the distributor shaft. Does anyone know of a source for the distributor bushings and drive gear rivet? Thanks, Pete
    • Pknapp
    • Thread
    • Replies: 2
    • Forum: Ford
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top