-
R
Hot ford won't start
Thanks everyone for the advise. I will run some test and see what happens. Thanks- ranba
- Post #1
- Forum: Ford 9N, 2N & 8N
-
R
Hot ford won't start
I have a 47 Ford 2N that doesn"t want to restart after it gets hot and it"s been running for awhile. If I shut it off for a few minutes after running it for an hour or so it will not start back up. I have to wait until it cool down. Any help would be great. Thanks- ranba
- Thread
- Replies: 4
- Forum: Ford 9N, 2N & 8N
-
R
Main Adjustment Needle
Thats funny,,just got the Carb from this web site about 8 or 9 months ago. -
R
Main Adjustment Needle
Trying to figure out why my 2N runs perfectly smooth when the Main Adjustment Needle is pulled all the way out. As soon as i put it back in it starts missing out real bad. I don"t even have to screw it in, i can put my finger over the hole where it goes and it will start missing. Any help at all... -
R
Firing Order
Ok,,I'm not real great when it comes to electronics and firing order and stuff so here's my question. I have a Ford 2N, firing order is 1-2-4-3. Distributor cap has 1-2-3-4. How are the wires suppose to be ran? -
R
conversion kit
Just wondering if replacing points with electronic conversion kit is a easy job or not?Thanks -
R
starter
Went to start my 2N this morning and heard some clanging noise. After about 3 times of this the noise went away and now the starter just spins. What in the world happened?- ranba
- Thread
- Replies: 1
- Forum: Tractor & Farm Talk
-
R
Starter
Went to start my 2N this morning and heard some clanging noise. After about 3 times of this the noise went away and now the starter just spins. What in the world happened?- ranba
- Thread
- Replies: 1
- Forum: Restoration Processes
-
R
Need Help With Carb
Just got a new carb for my 2N and was wondering how to set the screws on it. Missing out pretty bad.- ranba
- Thread
- Replies: 1
- Forum: Restoration Processes
-
R
Help--- Carb
Just got a new carb for my 2N and was wondering how to set the screws on it. Missing out pretty bad.- ranba
- Thread
- Replies: 3
- Forum: Tractor & Farm Talk
-
R
Lower Link
I have a 2N and it is leaking hydraulic fluid at the lower link. I tried to take the bolt off thats holding that piece on but the whole thing just spins. How do you go about replacing these parts? Thanks- ranba
- Thread
- Replies: 2
- Forum: Tractor & Farm Talk
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy