(800) 853-2651
SHOP NOW

Recent content by Red D

Yesterday's Tractor Forums
  1. R

    Farmall M head gasket question

    Leaking head gasket on my recent bored out rebuild, is this because the stock gasket it too small and 'exposed' more now that it's bored out?? Where can you get a better Head gasket??
  2. R

    front to back rake (wheel stance) much difference?

    Look at the diagram as if it were the rear hitch, As the front goes up, the rear hitch swings inward, under the rear axle, shortening to less than say 18 inches
  3. R

    John Deer rims

    Always wondered why they put 36 inch tires on the newer 520 tractor when the older B had 38 inch? Farmalls had 36 inch on the older M and the newer Super M had 38 inch
  4. R

    colder spark plugs

    Try this again 386 = D16 3116 = D18
  5. R

    colder spark plugs

    386 is the same as a D21, Hotter than a D18
  6. R

    Puller Slogans

    If it's not RED leave it in the shed!
  7. R

    Break in procedure ...please advise

    You need to keep the oil spraying around under the pistons and up onto the cam, Idling is a no-no for the cam, Did you coat the cam or lifters with STP or similar cam breakin lube when you installed the cam?
  8. R

    Mr. Baker - Cam math question

    On a Briggs cam, make a fixture to hold the cam then heat the cam with a torch and twist the cam to split the lobes to give it more overlap between the lobes, or cam advance on the gear drive end.
  9. R

    1100 massey fly wheel adapter

    Let me know what you came up with to solve the problem, I turned a spacer out of aluminum and drilled 6 holes using a flywheel as a pattern for a sprint car, back in the day. Still got the spacer.
  10. R

    New Oliver Puller.

    Are the wheele bars hooked to the hitch?
  11. R

    J D spinning out

    You have to take in to account the rotation of the Earth, In what direction are you pulling? North,South is more sensitive to this than East or West Then there is the Moon pull effect, similar to the ocean tides. Start by weighing one rear tire and compare that to the other rear tire weight, my...
  12. R

    e gleaner

    Had found an Allis WD gas engine that had a one inch spacer plate between the head and the block. Never figured out why???
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top