-
R
Dearborn Plow
I have been looking for a 2 bottom 3 point plow. I have seen some Dearborn plows that don't have chains to center the coulters and keep from damaging the tires. Do all Dearborn plows supposed to have chains?- Retcol
- Thread
- Replies: 2
- Forum: Ford 9N, 2N & 8N
-
R
Massey 44 Questions
A friend of mine just purchased a 1949 Massey 44. We were wondering what is the purpose of the plate on the drain pan next to the oil drain plug?- Retcol
- Thread
- Replies: 1
- Forum: Massey-Harris & Massey Ferguson
-
R
Ford 2600 clutch pedal rod and tractor surging
I was on a tractor ride today and my clutch pedal went flat. When I stopped the clutch pedal rod was bent. I got it back but it has a curve in it now. A guy had a small pin and we were able to hook it back up and finish the ride. Is that rod supposed to be perfectly straight? Can I put it in a... -
R
Ford 640 with a Sherman
Mine has the underdrive, standard and overdrive. I was looking for the top speed in overdrive and wide open throttle. -
R
Ford 640 with a Sherman
I just purchased a Ford 640 with a Sherman Transmission. What is the top speed? -
R
Tires Spinning
i had to load my Ford 2600 on the the trailer today. The grass was wet so I went to drive up on the trailerthe tires were just spinning. What can I do to prevent that from happening? My trailer is a PJ tilt with a strip of metal before the wood. -
R
Ford 2600 Wouldn't Start
I was getting ready for a tractor ride on my Ford 2600. I turned the key and nothing happened. I tried a jump start and that failed but I kept moving the high and low range shifting lever and then got dash lights. Then the tractor started. Is this a sign of a problem with the neutral safety switch? -
R
Ford 2600 Rearend leaking
I noticed an oil spot under the rear end of my Ford 2600, what is the most likely cause of this? -
R
Squeaky Universal Seat on Ford 2600
That is the obvious answer but it is hard to apply it when I can't determine where because it only squeaks when the tractor is being driven. -
R
Squeaky Universal Seat on Ford 2600
I have a Universal Seat on a Ford 2600. Everytime I hit a bump it squeaks. Is there any type of fix versus having to replace it? -
R
Ford 2600 Light Switch Knob
Thanks for the advice. It worked. Knob is now on. -
R
Ford 2600 Light Switch Knob
I bought a light switch knob for a Ford 2600 from my local CNH dealer. How do I install it? it only goes on the switch a little bit and won't saty. Help -
R
Ford 2600 Idle speed
What is the proper idle speed for a Ford 2600? Right now it idles at 1000 rpm. My mechanic can't get it below that level. What could be wrong?
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy