(800) 853-2651
SHOP NOW

Recent content by RichS

Yesterday's Tractor Forums
  1. R

    Three point stump grinder

    Email sent. White 2-155 and White 6144 both 150hp tractors - Palestine, Texas - Fully depreciated Make offer
  2. R

    Three point stump grinder

    I have a Miller Pro150 (they have been sold) needs 3 remotes,up/down,side to side, extend and 100-150hp 1000rpm pto, wights just over 2000lbs. Takes longer to get to the stump and position than it does to grind the stump.You end up with a foot deep hole and chips. Works great, used on about...
  3. R

    couple auto body work questions on an old pickup.

    Simple answer: 100-200 hours(depending on work required this could be low) at 60-100 per hour.
  4. R

    Stump grinders

    I have a Miller Pro-150, needs 75-150 hp, 1000 rpm PTO, 3 remotes, weights 2370lbs, 30 inch cutting wheel. Takes longer to move to stump and position (Minutes) than to get rid of stump. Hydraulic positioning of cutting disc with swing, lift, and telescoping functions, all controlled from the...
  5. R

    White 6144 Hydraulic issues

    The 6124-6144 Whites use a Massey 32x32 Dyna 4 transmission and rear end, hydraulic system. It is not like the 2-155 I had prior to the 6144.
  6. R

    White 6144 Hydraulic issues

    I have a 1996 White 6144 with the 32x32 transmission, while disking the Hydraulic Filter Restriction light came on. All hydraulics worked, 3 pt, remotes, and transmission. Replaced both filters right and left side. After about an hour of running in 70 degree weather, the Hydraulic Filter...
  7. R

    wiring diagram for a m670 super late model

    Here you go
  8. R

    565 Plow Questions

    I am in need to two cushion trip beams m/p for a 546, do you know of any place that has a salvage 546?
  9. R

    New Skid steer

    ASV was bought by Terex in 2010-11 time frame. I use a 2007 RC100 ASV (2500 hrs), most used implement on the Ranch. Fecon Mulching head, Pro Skid mower deck, grapple bucket, regular bucket, Danseur posthole auger, fork lift forks and bale spear. Changed tracks at 1500 hours, present set will go...
  10. R

    Agco White 6124

    I use a 1996 6144, same as the 6124, except it has an intercooler and 25 more HP. 12 valve Cummins is rock solid. Use it for baling, tillage, bush hogging. Creature comforts are quite good. Very good power, smooth transmission, very reliable. The 32x32 dynashift transmission is great for...
  11. R

    Cummins 5.9 Conversion

    1996 White 6144 uses a 5.9 Cummins with CPL # = 0599 replaced by CPL 0834 147HP with intercooler.
  12. R

    MM wire Hay baler?

    Grew up baling with one of these balers. It has a vertical plunger, right where all the damage is, would take a lot of new iron to get it all straight again, plus the Wisconsin V4 is more than likely frozen, at least the valves are. Made very heavy bales, but rarely missed a tie. Good luck if...
  13. R

    478 Hercules

    Search for a LDT 465 = Military version of the 478. 2 rebuilt on eBay right now $2500-2600 Put your exhaust/turbo/Injection pump on the 465 (22 to 1 compression) will provide more power than the original 478 (17 to 1 compression)
  14. R

    White 6144 PTO Seal Replacement Help

    1996 White 6144, leaking PTO seal (3383568M1) thought it would be no problem. Pulled PTO shaft, removed small metric screw in between the open area of the clip ring, removed large clip ring. Now I cannot get the sealing holder off (3582889M1). Any Ideas on how this is removed, I have tried...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top