(800) 853-2651
SHOP NOW

Recent content by RickyP

Yesterday's Tractor Forums
  1. R
    Expired

    Wanted Wtb allis g with cultivators

    Looking to purchase an Allis G with cultivators.
  2. R

    Need a little help

    If it has a fuel bowl on the bottom of the tank, take the glass bowl off after you have cut the fuel off. Fill it with B12 chemtool carburetor cleaner and put it back on. Also there is a screen in the fuel bowl area that could be clogging up. You have fuel problem. For some reason the fuel...
  3. R

    VAC Overhaul kit?????????????

    Where is the best and cheapest place to get an overbore overhaul kit for a VAC? Thanks, Ricky
  4. R

    VAC hyd's differences????????????????

    I have a 51 Vac that has an eagle hitch on it. I brought one home tonite that has a hyd valve by the belt pulley and a cylinder on the opposite side that runs a three point system. Is this as strong as the eagle hitch system? Just wondering which tractor would be best to fix up. Thanks, Ricky
  5. R

    D17 head help needed please??????????????????

    I pulled the head off of my D17 Gas yesterday. When I unbolted it some of the metal right under the bolts broke loose. There seems to be some kind of liner that goes around each head bolt. What do I need to do? Can these be replaced? Do I need to even worry about this? It was a small...
  6. R

    Will a D17 make a good loader chore tractor???????

    The loader hyds is run off of the PTO and it stops everytime you push the clutch in. Just wondering what you all think. Ricky
  7. R

    Does a D17 have a handclutch????????????????

    I am looking at a D17 with a loader. The loader is driven off of the pto. I was wondering how you would keep the loader running if it didn't have a handclutch. I am just unfimilar with Allis's. Let me know if this is a good loader tractor? Thanks, Ricky
  8. R

    Help with hooking up power steering on 400lpg

    I took the Behlen unit off of one 400 to put on another one. The parts tractor had a fitting that came out of the cast iron block on the left side of the dash. The one I have doesn"t have the place for the fitting. Can I install that by drilling a hole and tapping it? Can I just hook it up...
  9. R

    1066 front end parts

    I need to order some parts for the front end of my tractor. Can someone send me a parts list for the front end. I need to know if there is a bushing on the pin in the steering cylinder. Thanks, Ricky
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top