(800) 853-2651
SHOP NOW

Recent content by ROADMAN1

Yesterday's Tractor Forums
  1. tomstractorsandtoys

    Some sale prices today

    I was at a consignment sale in Polo IL today. Some prices, good 4020 gas $3800,4010 diesel wide front $7000,3020 gas wide front $4500,nf gas $4400. Side console 3020 gas $4300. 4440 nice $26,000. 4430 cab powershift $16,000.Nice original IH 706 gas $3450 good 806 diesel wide front $6,000. I...
  2. R

    Hyd. Control Valve

    Thanks TOH and Jock(OR) Great advice. I'll do this check this weekend. I never would have thought about this method of checking for internal leaks on a Hyd. cylinder. Thanks again Clay
  3. R

    Hyd. Control Valve

    I've been able to work the lever a little and stop it from leaking down as fast as it is now. This does not work now so I assumed it was the control valve. Is there any way to determine if it is the cylinders or the valve?
  4. R

    Hyd. Control Valve

    The Hyd. Control Valve on my 1957 Ford 850 loader (see attached photo) is allowing hyd. fluid to bypass causing the bucket and arms to leak down. Can this control valve be taken apart and "O" rings replaced and if so how do I get it apart or should I remove the Valve and have a Hyd. repair shop...
  5. R

    8N Distributor

    Yep Bob you are right. It is aluminimum to aluiminum. If I can't get it loose, I guess I will have to buy a distributor and the cover. It's not looking good to save either one. Clay
  6. R

    Dexta rearend

    I just got a 1962 Fordson Dexta that was going to the scrap pile. It has a 3 cylinder desil engine and a high-low transmission. Haven't looked at it much but the rear tires and rims look like the same as on my 850. I was going to ask the same question this morning about any of the parts being...
  7. R

    8N Distributor

    Just read all the post this morning. I appreciate all the response. I sure the distributor should come out of the housing. After soaking with ATF, I finally got the shaft to turn by tapping lightly on the gear. Still can't get the distributor to turn. I will try a little heat tonight and...
  8. R

    8N Distributor

    Old: I have it off the engine. Its just the distributor and the housing. Got everything freed up on the engine except for that. I put it in my vice to work on it. I guess heat is the next option. Clay
  9. R

    8N Distributor

    Yep. Tried the strap wrench like you suggested about a week ago. Let it set another week in ATF and diesel and tried it again. Lightly tapped on the gear with a small hammer and chisel. No luck. This thing is really stuck. My next option is heat but I wanted to ask you guys is it would...
  10. R

    8N Distributor

    Yep. I know not to put my blow torch to it. I have one of those cheap hand held torch that doesn't put out a lot of heat. I was going to just heat it up a little and see if it would loosen it up. Just wondering if a little heat would hurt the cast housing. Clay
  11. R

    8N Distributor

    Yep. I know not to put my blow torch to it. I have one of those cheap hand held torch that doesn't put out a lot of heat. I was going to just heat it up a little and see if it would loosen it up. Just wondering if a little heat would hurt the cast housing. Clay
  12. R

    8n Engine Ready for Primer

    I know this question has been asked a lot but here it is again. Got my engine ready for primer. Going to prime it before I start going back togeather with the new parts then wash and reprime after it is running. It is mostly paint free. I bolted most of the parts back on it so I will be...
  13. R

    8n Engine Rebuild

    Thanks Bill: Just simi-retired from Memphis. Lived there for 23 years and now I am in Central Louisiana. Kinda miss Memphis. Clay
  14. R

    Fordson Dexta Help Identify

    Thanks: Probably going to part this tractor out. Got everything but the head and exhaust. Been sitting for 7 or 8 years. Clay
  15. R

    8n Engine Rebuild

    I've read in previous post that some people are dead set on the tolorances shown in the F-04 manual. If you are planning on bushogging 10 hours a day in 100 deg. weather you need to follow all the guidelines. However if you are only going to load and unload the tractor for shows, you can have...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top