(800) 853-2651
SHOP NOW

Recent content by Rob Bishop

Yesterday's Tractor Forums
  1. R

    1135 PTO

    I've tried that. Have about 1/8" top and bottom before it bottoms out
  2. R

    1135 PTO

    My 1135 PTO engages with the valve in off position. As soon as hydraulics kick in about 15 seconds later pto comes on full power. If I Crack line from valve to pto it stops. There is always oil flowing through valve but it is slower when in off position. Borrowed a valve off neighbours 1100 and...
  3. R

    Older 2-105 Dual fuel tank

    Can someone please explain to me how the dual fuel tanks were plumbed in the older 2-105? Recently bought one and the top tank has been unhooked and all lines removed. I understand vacuum pulls fuel to top tank and top tank to fuel pump. Just wondering where to run all lines. And which tank...
  4. R

    1135 weak 3pth

    Bought a nice 1135 from and estate sale. Wasn't much info on tractor. 3 pth was plumbed into remote. Hooked it back up to see what was going on with it. It'll lift slowly but if I stand on it it stops. Draft position doesn't change anything and linkage all looks good and in place. All other...
  5. R

    1150 Hydraulics

    Recently acquired 1150. Tractor works great except for hydraulics. When you lift an implement and return valve to center, the implement drops. Like its on float. Happens on both remotes. 3pth and steering are good. Changed Hyd oil and filter. Cleaned screen in trans. Any ideas? Also under...
  6. R

    504 torque amplifier

    Bought a new to me 504 recently. When you pull the torque handle nothing happens. Found a video showing how to adjust linkage, it was way out but still nothing. I'm thinking it may be locked in low because it's slower than death on road but it does hold back on hills. What could be wrong and how...
  7. R

    Hydro 100 steering problem

    My hydro was leaking from steering valve under steering wheel. Got the seal kit, pulled the wheel and replaced the seal. Everthing went smooth, didnt use hammer or impact on it. Now it's steering hard. Went from steering with one finger to both hands. Any ideas on whats going on?
  8. R

    1440 MF baler

    Thanks for the info. I'll check it over with that in mind
  9. R

    1440 MF baler

    Im just getting set up to sell hay. Found a MF 1440 baler in good shape really cheap. Just wondering if they are a good starter baler and what to look for on it. Also wondering roughly how heavy a bale they make. My plan is to only use it a couple of years till I can afford better. Thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top