(800) 853-2651
SHOP NOW

Recent content by rosedale123

Yesterday's Tractor Forums
  1. R

    JD 60 power steering plug placement

    My dad and I have installed power steering on a JD 60 and would like to drill the hole in the front nose piece to access the fill resevoir ( if that is the right word). Can anyone give me some dimensions as to where the center of that hole should be? Like maybe from the seam between the hood...
  2. R

    ammeter issue- I think simple??

    that is how I have I have it but it doesnt read anything...If a battery is fully charged will an ammeter not read anything? Just thinking.....
  3. R

    ammeter issue- I think simple??

    I have a new ammeter hooked up in a one wire alt system. I have one wire from the alt going to one post of the ammeter and the other post on the ammeter going to the battery. With the motor reved up I show 14 volts ( or close to that) on each post of the alternator and also at the positive...
  4. R

    b414 carb

    i have gotten my B414 back together and I can get it to run ok but I have to "mess" with the choke to keep it running . It is a Zenith downdraft VN ( I think VN). Where should my initial high and low needles be we set ( # of turns) and the float level ?I think the float may be by culprit ( or...
  5. R

    got in a hurry...

    i did not describe it correctly ...in tapping the screwdriver with the hammer it got off course and damaged the outer most portion of the groove ( "widened ' it)..not full depth, just the outer portion... not sue how to do the picture thing... electronically challenged
  6. R

    got in a hurry...

    Like a duffis I got in a hurry trying to remove the stuck piston rings and I was doing ok until I got to the last piston. I got all the rings off but while trying to get the compression ( top) ring my screwdriver got a little off and slightly got into the piston. Is that "death" to that...
  7. R

    stuck pistons

    got it...i think ill just use oil/wood/patience thanks man
  8. R

    stuck pistons

    I ma working on getting the stuck pistons out of my B414.... I have been successful on 2 of the 4. I have been soaking the other 2 in kroil. th get underneath has give the last 2 a couple of whacks using a hammer a piece of wood but no luck yet. I have found a copper rod ( I think it was...
  9. R

    getting out stuck pistons

    sorry.. i meant to put this on the formal forum....but if u have advice i am all ears
  10. R

    getting out stuck pistons

    So I have been working on getting the stuck pistons out ...I have been successful getting 2 out and have the other 2 still soaking in Kroil. I have been using a piece of wood to "pound " from the bottom. I have found a piece copper rod ( I think it was a ground rod )...would the copper be...
  11. R

    motor stuck

    just checked..no stuck valves. I will take your advice and be patient...learned my lesson!
  12. R

    motor stuck

    Thanks for your reply..and I know from this board you are "expert"....will a motor get stuck that quick ? although it had been dry ( no oil ) for the last several months. I just never have had this happen and didn't know it could that quick. I will follow your advice. Many thanks
  13. R

    motor stuck

    ok..i am really stumped. I have B414 that I am restoring/ repainting. It ran before I started in on it. I have it mostly together and took the plugs out to check compression. I did no internal motor work except set the valves. So I hit the starter expecting the motor to spin but ii moves...
  14. R

    B414

    Not really but I need to check the model number of the Zenith carb that is on it. Mostly, it is the pressure regulator that perplexes me..... guess when I get it to the point or running I many understand its need. Hmmmm
  15. R

    B414

    oh yeah, the carb is a Zenith
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top