(800) 853-2651
SHOP NOW

Recent content by runsred44

Yesterday's Tractor Forums
  1. R

    Farmall M 248

    Thanks, time for some new pistons.
  2. R

    Farmall M 248

    Hey guys, new member here again, thanks for being patient with us new guys asking these questions. On my C248 with 4" bore and IH 4009 Z pistons, I measured .100/.102 on top piston grove, all I found so far is new ring sets come with 3/32 or .093/.094 rings, would that much clearance cause...
  3. R

    M C248 sleeves

    I thought the same thing when I looked at their website and it showed kits for flat and stepped head pistons. I probably never put it in my cart just called them to ask about sleeve O.D. and wrist pin size since I have the odd ball 1" wrist pins.
  4. R

    M C248 sleeves

    Thanks guys, I appreciate the comments. I tried YT first, over a month ago, the kits were not available and still not available today. I ordered from a different supplier and got Reliance cylinder/piston kits. (sleeve, piston, rings and pin). Their website said the kit was for 4.125 parent...
  5. R

    M C248 sleeves

    Gentlemen, I got new cylinder sleeves for my M C248. I can push the sleeves all the way down in the block, spin them and pull them out by hand. What are your thoughts on using permatex 64000 or loctite 640 sleeve retainer to secure them in the block? they're supposed to be good up to 400...
  6. R

    Super mta head bolts

    Thank you for the info. I'm rounding up parts to put my C 248 back together.
  7. R

    Super mta head bolts

    Jim, thanks for posting those pictures of the head studs, I didn't see your link at first.
  8. R

    Super mta head bolts

    Thanks for that post D Slater, you answered my question on where the 2 washers went. Can I ask what manual you have that showed the torque specs? Also do 2 head studs stick up a little higher for the governor bracket?
  9. R

    Farmall M rebuild

    Thanks for the information. I've been looking around online for availability and prices. I called YT, was told they did not have any in stock. I'm still looking.
  10. R

    Farmall M rebuild

    Hi guys, new member here. I'm rebuilding a 1944 Farmall M, C 248 engine with 4" sleeves. I'm looking at sleeve/piston kits, (are any made in usa, whats good)? Can I replace my flat top pistons with stepped head? (read that I need to change distributor drive to reduce advance), where can I...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top