(800) 853-2651
SHOP NOW

Recent content by smalltimer

Yesterday's Tractor Forums
  1. S

    Chisel plow ?

    Thanks I'd really like to find a 7 shank disc chisel but they're few and far between around me
  2. S

    Chisel plow point ?

    Yeah unfortunately I'm in Indiana
  3. S

    Chisel plow point ?

    Is it OK to run 3 twisted points on a rigid shank chisel plow? Been doing some searching and reading up on chisel plow points and on some other forums a few people commented that it isn't advisable to run 3 or 4 inch twisted points on rigid shanks due to them not having the give or flex of a...
  4. S

    Chisel plow ?

    Is it OK to run 3 twisted points on a rigid shank chisel plow? Been doing some searching and reading up on chisel plow points and on some other forums a few people commented that it isn't advisable to run 3 or 4 inch twisted points on rigid shanks due to them not having the give or flex of a...
  5. S

    White 2-155 over/under question

    Hi all I'm going to look at a white 2-155 tomorrow. It's supposed to be a 1986 model year which should make it a series 3. I spoke to the salesman on the phone this afternoon and he said they had a guy who knew whites pretty good come look at it and he said the over under direct needed adjusted...
  6. S

    White 2-155 over/under question

    Hi all I'm going to look at a white 2-155 tomorrow. It's supposed to be a 1986 model year which should make it a series 3. I spoke to the salesman on the phone this afternoon and he said they had a guy who knew whites pretty good come look at it and he said the over under direct needed adjusted...
  7. S

    1941 John Deere B throttle

    Thanks everyone I'll give everything a try when I get some time.
  8. S

    Co-op E3 spark plugs

    Thanks everyone hopefully I'll get to this sometime this winter. I'll definity try plugs only first and clean the points. Also rebuild the carb with a kit.
  9. S

    John deere 55 combine questions

    I have a few questions about john deere 55 combines and other models in that series. Going to be looking for a square back one in the next year or so to use on about 20 acres that I will rotate between beans and corn. 1 are filler plates needed to run corn on these? I've seen some people say you...
  10. S

    Co-op E3 spark plugs

    Hi, this winter I am going to try and get my dads 47 Co-op E3 that has been sitting for a few years running again. I am planning on doing an ignition tune up on it plugs wires points cap rotor etc. I was wondering what are the best spark plugs to run in it? And any of the other ignition...
  11. S

    1941 John Deere B throttle

    Hi everyone I have a 41 John Deere B. I got it out yesterday after it sitting for a good while to do a little plowing. The throttle lever won't hold full throttle position, it drifts back to about 1/2 throttle once you take your hand off the lever. It will hold position from low idle to about...
  12. S

    The 4020 is ready for field work

    Haha no it's not turboed unfortunately
  13. S

    The 4020 is ready for field work

    If I remember right its a 1965 and yes it's synchro
  14. S

    4020 ready for field work

    I know what you mean.. Still have the original muffler and I'm debating on putting it back on. Seems the older I get the more I like mufflers and I'm only 36.
  15. S

    4020 ready for field work

    Dualed and weighted up my 4020 this weekend waiting for it to dry some then it'll be working ground. It'll be pulling a IH 480 disc about 14 ft wide with the folded up. Hope grandpa is smiling down.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top