(800) 853-2651
SHOP NOW

Recent content by terryz

Yesterday's Tractor Forums
  1. T

    Case 930 instrument panel

    I have a case 930 that I am repairing the instrument panel. My data plate shows the model to be a 931 , ser # 8333151. The online parts book only shows different versions of an automotive style instrument cluster. My panel is composed of individual round gauges and individual idiot lights...
  2. T

    M M model V oil filter

    I have a MM model V that has an oil leak at the base of the oil filter canister. It leaks between the canister body and the large washer that the the oil line screws into at the bottom . I don't see any way to unscrew the standpipe to disassemble the housing. The parts book only lists the...
  3. T

    L3750DT f.axle seal replacement

    Thanks for the reply. I have the parts book.
  4. T

    L3750DT f.axle seal replacement

    I am replacing the front axle kingpin seal on a l3750dt. The new seal part # 32590-43620 is different type of seal than the origional. I am not sure which way the seal is installed; with the metal face up or down. thanks, Terry
  5. T

    Kubota D902 engine

    Has anyone Had experience with aftermarket head gaskets on the D902 engine? The aftermarket gaskets are a layered metal gasket, a lot different than the origional one or should I bite the bullet and get an o.e.m. one or take chance on possible coolant seepage?
  6. T

    RTV900 front fenders

    I am repairing the floor of a rusted out rtv800. The front inner steel fenders are completely gone. The shape is pretty complex and hard to duplicate. Has anyone found an off the shelf fenders that could be modified to work ?
  7. T

    coolant heater Farmall 504 gas

    I have an older engine. There are no freeze plugs on the right side of the block. There are 3 on the left side; 2 about 3" below the top of the block, behind the carb & generator and one next to the block drain at the bottom of the water jecket. Trying to avoid knocking out freeze plugs until I...
  8. T

    coolant heater Farmall 504 gas

    I would like to install a freeze plug heater in a 504 with the c153 gas engine. Will the freeze plug by the drain plug on the left side of the block work ? On most freeze plug heaters the element is bent 90 degrees, or is there another freeze plug location that would work better?
  9. T

    1080 main hydraulic pump

    Your pump should be a pressure control ferguson pump with the relief valve bolted to the pump frame with 3 bolts. parts are no longer available for these pump parts. Unless you have a pressure control hitch, it is better to eliminate the pressure control parts including the arm in the lift...
  10. T

    IH 504 front axle pedastel replacement

    The replacement tricycle pedastel 380660r91, came with 1/2" rivets to connect axle shaft to the bottom of the pedestal. I have no way to swage these rivets. Can I use grade 8 bolts and locknuts or should I look for someone who can swedge 1?2" rivets? Thanks, Terry
  11. T

    farmall 504 tachometer

    Looking for a discontinued tach for a farmall 504 diesel tractor; part number 383090R91. There are plenty of gas engine tachs available {383089R91}. Does anyone know if there are any internal differences besides the printed rpm numbers on the face of the dial and if one would work in place of...
  12. T

    RTV 500 brake parts

    Looking for individual parts for the rear brake caliphers part # k7311-99470 on a rtv 500. I need seals & a piston to repair one. Kubota wants $ 400.00 for a complete new one.
  13. T

    RTV500 air flow sensor plug

    I have a kubota RTV500 that someone cut the harness plug for the eg672-44801 air flow sensor. The sensor is a Mitsubishi part with several numbers along with the kubota number; number 720113552 is printed by the harness plug. E1T23971 7609 00096 is printed under the kubota number. Kubota...
  14. T

    farmall 504, d188 engine sleeve question.

    It is a newer style block with the thin flange with the head gasket sealing at the block, not on the liner flange. # 3 sleeve which dropped down and was broken up by the crankshaft is close to spec height .001- .004" at .006". The other 3 are at .020". Apparently, I need to pull the sleeves and...
  15. T

    farmall 504, d188 engine sleeve question.

    I have a IH 504 with the D188 engine that I am rebuilding. The I & T shop manual calls for the sleeve standout of .001 to .004" The sleeves in the A & I overhaul kit are .020" above the block. Have the engine parts suppliers changed the specs over the years or am I missing something ? Like a...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top