(800) 853-2651
SHOP NOW

Recent content by tracman

Yesterday's Tractor Forums
  1. T

    Spark Plugs

    How do you check the new spark plugs out of the box? Ohmmeter? Spark tester?
  2. T

    Are new distributors pre timed?

    If that's the trouble try starting it an hour sooner :D :lol:
  3. T

    Problems starting my Ford 8N

    Thanks :D
  4. T

    Problems starting my Ford 8N

    Bruce, sorry about that, it was converted to 12 volts and has an unknown resistor and external coil.
  5. T

    Problems starting my Ford 8N

    Gentlemen, would this coil ( NAPA IC-4SB) be suitable for a 2n with a gutted front mount coil? No resistor(s) would be great!
  6. T

    Engine oil dipstick broken in early 8N

    Try "search" for '9N cut away'. There is some pictures there that might help. I imagine the engines to be similar. Although I am no expert.
  7. T

    Engine oil dipstick broken in early 8N

    [http://forums.yesterdaystractors.com/photos/29717_sml.jpg I am not sure this photo will come thru. But it looks like the dipstick is above the drain hole.
  8. T

    what a pain . . .

    Dell, just get yourself well soon. All the best, tracman.
  9. T

    Yet another no start - new symptom

  10. T

    Ford 2N running issue

  11. T

    Ford 2N running issue

    I had a similiar problem. 12volt updates can add an issue or two. After your tractor has started with the jumper in place remove the jumper after a minute or so of running. If it runs OK the problem is the spark is too week to fire on low compression and cold gas. You are probably flooding the...
  12. T

    Ford 2N running issue

  13. T

    OT - Garden Report

    I wish the stawberries looked that good around here. I can't beleive those tomato plants!
  14. T

    Voltage reading over resistor

    Where did you check the for the spark? Your plugs maybe fouled and wet with gas from trying to start and maybe over choking.
  15. T

    2N governor issues

    Just an update: I had a problem with governor causing overspeeding when the load was removed also it was very poor in picking up load as well. I found that the governor internal fork was worn. Good bad or otherwise I installed two 18 gauge 3/4 inch machine shims in front of the fork that I...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top