-
T
Case 8465 baler bale shape sensor issues
My mind sees the physical right controling drive left as well. Thanks for the input. Every little bit helps.- trentr
- Post #3
- Forum: Implement Alley
-
T
Case 8465 baler bale shape sensor issues
Have used an 8465 for many years. Currently struggling with bale shape sensors. They work erratically. Drive "left" has 2 arrows then 4 then 3 and just jumps all over the place. Drive "right " has 4 arrows all the time. Never changes. The monitor set up sometimes says adjust cw sometimes ccw...- trentr
- Thread
- Replies: 5
- Forum: Implement Alley
-
T
801 injector cam ring direction
801 has sat since I was last on here. Hooked up 12v crank a few times....no go. Hook up 24v and fired right off no ether. I am thinking of trying a new starter. I cleaned all connections and pulled starter apart and lubed it up. Helped cranking speed some but maybe still just a bit slow. When... -
T
801 injector cam ring direction
It starts the same wether is has sat 2weeks or 2 minutes so I was bot sure if it would be considered a "hot start" issue. The hydraulic head was "rebuilt" when I got it but I have been in there and it appears they just replaced the governor ring with a solid one and that is about it. I think... -
T
801 injector cam ring direction
Well the 801 runs pretty well. 841. I think. Diesel. Anyway it starts when pulled. But off the starter it will only start if hooked 24v AND a snort of starting fluid. When pull starting in 4th it slides the tires for a bit before turning engine over. So I assume pretty good compression. Run it... -
T
801 injector cam ring direction
This project is a low priority and I get a couple hours here and there between a busy life of a full time job as a machinist, small engine repair and auto repair on the side , as well as keeping 3 teenage boys in line. First injector pump so learning as I go. I'm trying. -
T
801 injector cam ring direction
Well I have fuel shot out of 3 injector lines now. Not sure what is up with the 4th yet. Got some smoke out the exhaust but no fire yet. Fuel seems to be leaking between pump housing and hydraulic head now and I lined my pump timing marks and the flywheel was on about 12 degrees. So it looks... -
T
801 injector cam ring direction
That is how I have it now. I finally was able to look and see some wear on the cam ring lobes which gave me a pretty good idea. I have the pump reinstalled, hope to give it a pull tonight. Thanks for the help guys. -
T
801 injector cam ring direction
More info. Acquired tractor with rebuilt pump not installed. I have never had it running. Return line clear. Air bled out of filter housing. Pull tractor until i get occasional drips from all lines at the loose injector nuts but never more than an occasional drip. Metering valve free moving... -
T
801 injector cam ring direction
I have a ford 801 diesel, 841d?, IDK anyway the roosamaster pump has cc in the model number so counter clockwise. When installing the cam ring, you are supposed to place the arrow indicating pump rotation "facing up". My question being is "up" as the pump sits on the tractor or "facing up" while... -
T
Seeking Ford 4000 injector lines
From a 1938 John Deere A rod to steering clutch parts for a HD6G Crawler and now Ford injector lines, these forums and the helpful people.on them keep old iron up and going. Thanks a million. -
T
Seeking Ford 4000 injector lines
Well I'll be dang. I am no tech wiz but I have done my fair share of internet parts ordering but I dang sure had not had any luck finding these. Even with you all directing me it was still an embarrassing struggle. But there they are! And an injector pump that I thought you could no longer get... -
T
Seeking Ford 4000 injector lines
All I could find was for 3 cylinder models. I need banjo fitting style for roosamaster pump -
T
Seeking Ford 4000 injector lines
I have an old style 4000 4 cylinder diesel. Roosamaster pump. I have no injector lines. I cannot find a source for injector lines. 1. Does anyone know the fitting size/style on the injectors? 2. Are there any other lines that would work. Just looking from a distance the 806 we have seems to...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy