(800) 853-2651
SHOP NOW

Recent content by WALTER GORMAN

  1. W

    gears grinding Ford 8n

    Thanks for your response Royse I'm gonna change the fluid and hope this helps Appreciate your help....Walter
  2. W

    gears grinding Ford 8n

    Thanks for your response....it does shift. I idle it down in order to get it to shift. The fluid looks milky and I've never changed the fluid since I've had the tractor(12years)....I'm gonna change the fluid and hope this corrects the problem. I'm trying to avoid splitting the tractor. Thanx...
  3. W

    gears grinding Ford 8n

    Good evening...I'm having trouble shifting gears in my Ford 8n (gears grinding and hard to get in gear) Can Old Hydraulic Fluid cause shifting problems ? I've tried to adjust the clutch but no help. I'm hoping it's not my clutch.....Thanks in Advance Walter n Da Carolina's
  4. W

    8n Starter Help

    Thank you very much Bruce.....I am pretty sure I can get it done now....I hadn't remove the band :( Thanks to the Forum !! Walter
  5. W

    8n Starter Help

    Thanks Bob...I will try that...I think I understand what you've suggested....Walter
  6. W

    8n Starter Help

    Good afternoon Does anybody have an illustration or can explain how to use toothpicks to hold brushes back to put armature back in starter ? I have tried but cannot figure it out...thanks in advance Walter
  7. W

    8n starter

    Royse...thank you for the pictures and the advice. I think this is a better way for me....Have a Good Evening Walter
  8. W

    8n starter

    Thanks for your response Bob Walter
  9. W

    8n starter

    Hello Evryone I need help....broke bolt off in starter trying to tighten solenoid. Tried to drill bolt out...no luck. Can I use hole on other side of starter to secure solenoid ? can I mount the solenoid some other way rather than on top of starter ? Thanks in Advance Walter
  10. W

    8n Starter Rebuild

    thanks JMOR located shop that will solder new brushes in for me a a reasonable price. Be Blessed
  11. W

    8n Starter Rebuild

    Thanks Dell I will keep your tips in mind when I get ready to put it back together ..I appreciate it. Be Blessed
  12. W

    8n Starter Rebuild

    Starter rebuild 1951 8n......I am a Firsttimer, looking for help rebuilding starter Is there an Instructional video or picture illustration showing how to put brushes in and just overall how to ? Any help will be greatly appreciated....Walter Thanks
  13. W

    One Inch Round Bore PTO Shaft

    thanks SoundGuy I will look into it...I am guessing that I might have to build the shaft the way I mentioned.
  14. W

    One Inch Round Bore PTO Shaft

    I am searching for a PTO shaft, Implement End... One inch Round Bore and Tractor End... 1 3/8 6 spline. This will go on 4 ft Challenger (Imco Finishing Mower) Any help that would point me in the right direction would be appreciated. Walter
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top