-
Watthour replied to the thread a good tyre slide hammer.I did the same. I am contemplating getting one of the newer battery powered hydraulic pumps since I also have Port-A-Power cylinders... -
-
I have a hyd bead breaker I use on air over hyd pump. I think the name was yellow jacket got from an auto part dealer. No beating...
-
Watthour replied to the thread Milwaukee Sawzalls - corded vs battery.When your 18V NiMH flashlight saw lasts this long, come back to discuss it: http://www.wwdsltd.com/files/MilwaukeeSawZall.jpg This...
-
-
Watthour replied to the thread RACOONS IN THE BARN.No doubt about it - You need a bigger cat.
-
We were over run by raccoons in all the outbuildings until these 2 Great Pyrenees became part of the farm. Now a raccoon does not dare...
-
Watthour replied to the thread Allis Chalmers B oil pressure gauge.If it is resolution that concerns you, a 30 PSI gauge with a 270° sweep will provide better resolution than a 20 PSI gauge with 90° sweep.
-
Hemorrhoid reverser kit.
-
Watthour replied to the thread Parts Cleaner Sovent.Limonene-D. It's been around for quite a while. It is slightly acidic, contains natural solvent oils and usually some alcohols and...
-
Watthour replied to the thread anyone else have this problem.So far, this one only prunes the lower limbs from the blue spruce, white- and Norway pines around my perimeter. I find sticks all over...
-
-
Watthour replied to the thread anyone else have this problem.It's not only labs, although they seem to have a propensity for thievery. How about this one? Standing on a short ladder one day...
-
Watthour replied to the thread Auction find.I also have a K&E, a Precision plastic, and a basswood/brass. I had to dig them out and couldn't find my round one (too easy to hide)...
-
-
Watthour replied to the thread Parts Cleaner Sovent.I've had one of those low-buck parts washers for about 20+ years. I've found that diesel fuel is actually pretty good for cleaning off...
-
Watthour replied to the thread Heavy rust primer goop.I use that regularly on raw castings coming from the foundry. They sit for months before machining to allow them to stabilize. It's...
-
-
Watthour replied to the thread Another vice question.Jorgensen.
-
Watthour replied to the thread Our farm’s new horse.That looks like a decent pick. The "plus" I think I see is that the rubber looks reasonable, and they may have been off recently...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy