Recent content by Wbalcorn

  1. W

    5000 blows steering cover

    Got back on my 5000 and straight the plate used some jd white silicone and new grade 8 caterpillar bolts installed plate and let sit for a day running fine now thanks for all your help
  2. W

    5000 blows steering cover

    I’m goin to get some grade 8 bolts to install the plate with since I have to remove it to check the end play on the sector shaft this tractor has been sitting for sev years because of this problem and I don’t know what has been done to it in the past
  3. W

    5000 blows steering cover

    It did warp but I put a straight edge on it and straightened it out before reinstalling going to check over the sector shaft endplay again don’t know how much it should be but apparently some steering works fine till it blows out the gsk.
  4. W

    5000 blows steering cover

    I have resealed the cover and replaced the bolt in the picture it was the same bolt both times bottom left right below the throttle control rod nut in the picture of the cover
  5. W

    5000 blows steering cover

    Thanks Bern I will get back at it tomorrow especially the the information on the link as I don’t have any technical information to guide me and the time you have to share your expertise to help me I will check the sector shaft closer. The reason you don’t see the broken bolt is because I have...
  6. W

    5000 blows steering cover

    I checked both shaft’s on the steering box the output shaft has 0 endplay but the steering shaft has about 1/4 inch could this be my problem
  7. W

    5000 blows steering cover

    Hey guys I haven’t hit any external obstacle to get a pressure surge it will blow out when I turn left and it popped the same bolt both times the one you can see at the bottom left I really appreciate all of your help this is a great tractor if I can just keep some power steering fluid in it the...
  8. W

    5000 blows steering cover

    Ok I will try that but shouldn’t the relief valve protect against spicks also does anyone have a diagram my system doesn’t have a steering valve with the 4 lines together or the cylinder under the radiator I will put some pictures on here when I get back to it thanks for your help
  9. W

    5000 blows steering cover

    Ok thanks I will chec it out okay thanks I will check it out I appreciate you time and info
  10. W

    5000 blows steering cover

    I have a ford 5000 with the late style steering system with the pressure hoses under the steering wheel I got to much pressure have not put a gauge on it yet but when you blow out the gasket from the plate on the right hand side of the s box and pop the head off one of the bolts twice something...
  11. W

    584IH hyd runs hot

    well friends I am still searching for my over heating hyd problem I am checking my unloading valve it is on top of the trans cover right under the seat I have looked in the manual about the unloading valve piston because when I removed the plug I noticed free play between plug and piston and the...
  12. W

    584IH hyd runs hot

    I have removed added on remote valve and got about 25psi does anyone know how much psi cooler circuit should have and what regulates press thanks for the help
  13. W

    To 35

    Thanks I am replacing clutch and checking clearance while this close thank you so much for the info
  14. W

    To 35

    Can someone tell me what the intake and exhaust valve clearance on a continent engine is has a number on block of z143a500p
  15. W

    584IH hyd runs hot

    thanks to all that have responded this is my first experience with this valve. I have done a lot of studying on it and got a i&t shop manual page 5 shows a exploded view and they do give a flow and press test also looked on line at flow charts they show a ta in diagram I don t have one.I...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top