-
N
Ford 601 picker value
I have a gentlemen interested in the Ford 601 Corn Picker I have. Curious on a ball park value of such an implement. Its in average working condition. I've used it to pick a couple fields years ago. It has been inside the whole time I've owned it and the entire time the last owner did as well...- nwford
- Thread
- Replies: 2
- Forum: Implement Alley
-
N
Van Brunt B Grain Drill Rate Chart
Looking for a rate chart for a John Deere Van Brunt model B grain drill. This one is a 16 x 6. Mainly looking for the grass attachment box rates.- nwford
- Thread
- Replies: 1
- Forum: Implement Alley
-
N
830 three cylinder hydraulic issues
I have an 830 three cylinder utility tractor. For the last year the three point hitch will no cycle up until the scv lever is cycled. Can hear the pump build pressure the the hitch will lift. Seems like once this is done once the hitch will work fine until the next day. Also the hitch lever...- nwford
- Thread
- Replies: 3
- Forum: John Deere
-
N
Ford 5000 clutch and PTO input shaft
I'm in the process of replacing the clutch in my 74 5100. Found wear on the splines in the drive hub for the PTO and the input shaft E4NN7A684AA. Can I remove this shaft after removing the rockshaft, PTO clutch and the upper rear pto output shaft? Appears it comes out the rear of the... -
N
3000 steering drag length
The ball joint on the rear of the drag link for the steering on my 3000 was getting loose. I have ordered a couple aftermarket ones but haven't been able to find one the correct length or with the correct size threads on the front of it. I can seem to find one or the other. The tractor has power... -
N
5000 Diesel overhaul kit
The 1974 5100 we have is getting tired. Been breathing hard the last couple summers. Plan on keeping this tractor for along time. Anyone have a recommendation on where to get an overhaul kit from? -
N
841 differential center housing
I'm working on an early 841 tractor. There is a slight crack someone appears to have welded on the differential casting. It has NDA 4024B cast into it. Would the center differential casting from a 860 be the same? Or what models would I be looking for? -
N
960 hitch pulsates while trying to lift
I'm working on a 960 I bought at an auction years ago. When I attempt to raise the three point the arms shake or pulsate on the way up with no weight on them. Does the same with 500lb of suitcase weights but it will lift them. I've swapped the hydraulic piston pump with on off of a working... -
N
Ford 3000 flywheel turning specs
Working on the clutch in my 1974 3000. It has the dual stage clutch in it. Have some small heat cracks in the flywheel. Does anyone have the service bulletin or info on how much can be surfaced off of one of these? Every one around my are is more familiar with green or red. -
N
601 corn picker mounts
I recently bought a 601 Ford corn picker. The person I bought it from had it on a 860, I'm putting it on my 860. I never saw his tractor so can't verify. The angle iron bracket that go under the axle don't seem correct. I cant hook the pto shaft up to the tractor. The husking unit seems several... -
N
Ford 601 Mounted corn picker
I recently bought a 601 Ford corn picker. The person I bought it from had it on a 860, I'm putting it on my 860. I never saw his tractor so can't verify. The angle iron bracket that go under the axle don't seem correct. I cant hook the pto shaft up to the tractor. The husking unit seems several...- nwford
- Thread
- Replies: 7
- Forum: Implement Alley
-
N
Ford 515 sickle mower breakaway
Have been messing with this Ford 515 three point sickle mower for a couple years. No matter what I try I can't seem to get the breakaway arm to hold as it should. It will release just driving across the yard with the mower down. I've adjusted the length three bolts holding the main the spring... -
N
Ford 515 sicklemower breakaway
Have been messing with this Ford 515 three point sickle mower for a couple years. No matter what I try I can't seem to get the breakaway arm to hold as it should. It will release just driving across the yard with the mower down. I've adjusted the length three bolts holding the main the spring...- nwford
- Thread
- Replies: 5
- Forum: Implement Alley
-
N
841 Diff casting number
I've been piecing and early 841 back together for awhile now. The previous owner must have had a differential failure because there is a patch welded on the bottom of the differential cast. Was previously a forklift. I found a casting of NCA4024B on the left side above the pto shift lever. Can... -
N
Looking for pinion shims
Working on an Elenco axle for my 841 tractor. Put new bearings and races in axle but having issus setting pinion bearings. Looking for shims with 7/16 inch ID 2 inch OD. Have gotten several shims from Vintage Power Wagon, but nothing thick enough. Looking for total thickness of .205 inch. Anyone... -
N
24t bale chamber repair
I got a John Deere 24t baler with a tractor I bought. The plunger is loose up and down at both ends of the stroke on the side closest to the pickup. I removed the plunger and have found the upper right (standing behind the baler) portion of the baler is worn badly. There is no wear plated or...- nwford
- Thread
- Replies: 9
- Forum: Implement Alley
-
N
Ford 5000 extendable lift arms
I've got a late Ford 5000. It has the three point lift arms that you can pull up on a ring, extend the ball portion out to hook to an implement. The ones on my tractor will not stay latched once I back up. I've replaced the leave spring and lock assembly with no luck. Any ideas anyone? -
N
3000 steering sector gears
Rebuilding a 3000 power assist steering box. Gears in it showed wear both on teeth and gears. Got both the single and double gear from A&I, they weren't even close to right. Any one had any luck with new ones from any supplier? -
N
Ford 5000 hyd pump idler gear
I've got a '74 Ford 5000 that I just bought. Noticed a bit of a howl when using the hydraulics. I removed the hydraulic pump and found the idler gear with casting number C7NN873A is worn. Any one know of a place to get a new aftermarket gear? No A&I, I've had plenty of issues with their...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy