(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. C

    Gibson SD Paint Color

    anyone know what brand and name of red paint they have used for a Gibson SD tractor? i know it's a wine or burgandy shade but i want to know what you have used.
  2. C

    MH PONY PACER WHEEL WEIGHTS

    i have 2 wheels weights that are for a Pony or Pacer but one of them has a 3 hole triangular bolt hole pattern, that look factory casting to me, what would it be for?
  3. C

    VA intake tube ice cold

    after i start my VA and run it for about 5 minutes it dies,the intake tube above carb is really cold . what causes that, what can i check or do to stop it.?
  4. C

    Unknown tractor

    Can anyone identify this tractor?
  5. C

    side panel difference on VA VAC

    can anyone tell me what the year or model difference is on these side panels are for a VA VAC?
  6. C

    VAC rear differential

    what would cause the rear differential to act like it has posi? i had to replace the rear and cleanout the trans housing etc then put it back together with no problems, but know when i have it jacked up on both side with both rear wheels off ground and turn them by hand to check both sides turn...
  7. C

    mounting VAC rear wheel center

    so i painted the rear wheel centers and rims on my 46 VA that has the 5 wheel wedges . is there a tick or method to mount the rim to the wheel center without scratching them up and without mounting the center to the axle? i have never done one a Case.
  8. C

    marvel carb parts

    anyone have these parts for a cable choke assembly?
  9. C

    VAC fan belt WITH generator

    anyone know a part number for a fan to be used with a generator on a VAC ? everyone sells them for use with out a generator.
  10. C

    VAC Governor

    after assembling the 9 ball bearing type governor on my VAC and connecting all throttle linkage, i cannot get any movement out of the governor. it went in with out any problems that i know of. all linkage is free a clear of any obstructoin, so it tells me there is something going on inside the...
  11. C

    Oliver Orchard ?

    got a shot at picking this up for cheap, but not sure if those orchard fenders are factory. i have browse around the net and all other Oliver orchard fenders are different, can anyone shed some light on what year and model this is?
  12. C

    VAC pedal spring

    anyone know where to get a new VT 2435 pedal feed spring?
  13. C

    VAC pressurized or non pressurized

    how do you tell if a VAC is a pressurized or non pressurized cooling system? i have a VAC that does not have a radiator or thermostat and need to order on but not sure what i need.
  14. C

    VA step plates 1949 and earlier

    can some provide the measurement on a early 49 an earlier step plate floor boards the part of the step plate where the diamond plate rolls on the outside edge, i need to know the length of that part. i think mine were cut down shorten , i have a set off a 50's but they are to long
  15. C

    Case VA axle housing

    Hello, i have a 1948 Case VA with standard front and i need a rear axle housing, and i have located one but the seller does not know what is came off of, before i drive 2 hours to get it, i want to give him the measurement it should be. i believe the VA VAC and VAO are the same correct?
  16. C

    VAC Head Difference

    anyone know what the difference is on the head based on the stud holes below each sparkplug? could it be the year? both are stamped VT-148.
  17. C

    Case VA year

    Is there a way to find out what year a Case VA is with just the engine serial number ? engine number is 72-B-18365.
  18. C

    kill switch wont ground out mag

    i bought a new single terminal kill switch, ran new 12 gauge wire from switch to magneto, i have good ground ,i have tested continuity on everything and it test like it should work, but it wont shut off engine. what else should i check or what could it be. i did take the wire off the switch and...
  19. C

    generator cut out

    what would be the cause for the point on the cut out relay that is piggybacked on the generator to not close when the tractor is running but when i push them closed it stays closed but when tractor is shut off they stay closed. 6 volt farmall b with a magneto
  20. C

    FARMALL B FAN ASSEMBLY

    I bought a new Fan assembly Part Number 701360R here on this web site, and it does not have any plug to oil it. do i need to drill and tap one so i can fill with oil or ?
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top