-
D
Kubota B7200 FEL to mini skid quick attach conversion?
I have a B7200 hydrostat 4wd with a front end loader. The bucket is shot on it. These older kubotas have the 4 pin style bucket attach. No quick attach. I'm planning on sacrificing the bucket and cut the 4 point pin brackets off. On to those build/attach a quick attach system for mini... -
D
Kubota D905E running a PTO generator?
I have a Ransomes Mower with a bad transmission. When it gets good and hot it doesn't move very well. I was thinking I could use this mower as a dedicated Engine to power a PTO generator. The motor in it is a 905E diesel rated at 23.5hp at 3600 rpm. I want to run a 7hp -10hp single... -
D
Waldon 5000 3rd function spool valve lever lock?
I have a 3rd function on my Waldon. I've added a quick attach and want to run a hydraulic auger. My question is if there is any way to make the third function lever stay put without holding it in the spring loaded working position. The issue Im having is that I can't constantly hold the...- dstanek
- Thread
- Replies: 5
- Forum: Crawlers, Loaders, Dozers and Backhoes
-
D
Ford 172 oil leaking bottom rear oil pan area
Have a new issue with this engine. Oil is leaking quite badly somewhere from rear of engine out of back ctr area of oil pan. I cant see worth a darn up in there. This happened after I just replaced the oil pan gasket. I put thin coat of permatex down on the rim of oil pan waited for it to... -
D
Ford 172 oil pump check with drill vid
Im seeing here that the pump is pumping oil while drill motor is turning, however a gauge doesnt read anything. When i put my finger over the hole i dont feel any pressure either. This motor is in a waldon loader and it sits on top of the steel gas tank. I may have to pull the motor to get oil... -
D
Ford 172 industrial engine mechanical fuel pump right one?
I bought this on ebay now I'm worried it won't fit or ruin my CAM if I try it and it's not the correct one. My Waldon is a 1976 so I don't know if this pump will fit or not... I've seen pics with the fuel bowl on the top. This one will put it on the bottom. Is it the correct replacement... -
D
Ford 172 industrial engine blown head gasket metal or non metal replacement?
Blew the head gasket between 2 and 3 cylinders on my waldon 5000. I was able to check it before tearing apart by blowing air in cylinder 2 and air came out of cylinder 3 ! So that explained the 60 psi in both cylinders when I checked compression. I ordered a head gasket that looks the same... -
D
Massey 205 diesel 3 pt hitch weight limit?
I have a 205 diesel industrial with a 200 loader and torque converter with the pedals F and R for instant reverse and forward with no shifting. I believe this is the reason there is not PTO shaft on this tractor. Anyway, I'm using the tractor to lift some pretty heavy red oak logs along with...- dstanek
- Thread
- Replies: 5
- Forum: Massey-Harris & Massey Ferguson
-
D
Ford 172 industrial propane MS carburetor
I have a waldon 5000 with a propane ford 172 industrial engine. It has the large marvel schebler carburetor on it. It hunts at lower RPM which I've read is usually a fuel starvation problem. In this case propane. There are no settings on this carb that I know of to adjust. I took it... -
D
Propane Century Vaporizer model H replacement for 172ci ford industrial engine
Can I use an Impco model J vaporizer on my FORD 172ci industrial engine as a replacement for the Century model H vaporizer that is on it now? The Impco model J is 86$ vs 369$ for the century model H. They look a little different with a couple of wires coming off of the century that are not on... -
D
BD2G Powershift transmission
Looking for transmission rebuild kit or individual internal parts, or a good used transmission for my BD2G POWERSHIFT dozer. Rhiner is out of business according to the website. Anybody on here with a lead on parts or good used tranny would be greatly appreciated. Thanks ! Wondering if the...- dstanek
- Thread
- Replies: 0
- Forum: Crawlers, Loaders, Dozers and Backhoes
-
D
Case 450 188 diesel
Looking at buying this dozer. Went and looked at it. Undercarriage seemed pretty good. Good sprockets pads pins and rollers. Starts good, steers and operates good as i can tell. The concerns i have are these. Made awful lot of clacking noise from engine area at idle. Couldnt tell where or...- dstanek
- Thread
- Replies: 6
- Forum: Crawlers, Loaders, Dozers and Backhoes
-
D
Massey Ferguson 205 3 cyl perkins diesel power steering conversion
Took a page out of Cary and Inno's power steering conversions. Followed their lead with a few mods of my own. Space is super tight on the 205 so I opted to bend my own hard lines to the power steering lines instead of running hydraulic hoses out of the new orbital steering valve. Didn't...- dstanek
- Thread
- Replies: 1
- Forum: Massey-Harris & Massey Ferguson
-
D
Massey 205 95mm vs 85mm tractormeter RPM gauge
I ordered a gauge set off of Amazon for my Massey 205 industrial. The RPM/hour gauge it came with was 85mm and my gauge is 95mm diameter. Someone previous to me found the correct gauge at 95mm or 3.75ish inch diameter that's in there now. I want to put a new one in with a light. Can...- dstanek
- Thread
- Replies: 5
- Forum: Massey-Harris & Massey Ferguson
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy