(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. A

    Worried about sounds behind oil pan

    Took the 8N (it's a 64 2000, but really just the phase out of the 8N, not the real 2000) out this morning and we were dragging a leaf rake, not much work at all, and was hearing an intermittent scraping sound coming from bottom of tractor. Somewhere between me and the oil pan. It would come and...
  2. A

    Worried about 8N sounds behind oil pan

    Took the 8N out this morning and we were dragging a leaf rake, not much work at all, and was hearing an intermittent scraping sound coming from bottom of tractor. Somewhere between me and the oil pan. It would come and go randomly, that is not due to a load, but only happened when tractor was...
  3. A

    Ladders and Gates

    Are we guilty of this ? https://www.hagerty.com/media/opinion/avoidable-contact/avoidable-contact-92-gates-and-ladders-all-the-ways-old-people-kill-young-enthusiasm/?utm_source=SFMC&utm_medium=email&utm_content=21_February_3_Newsletter_NewDD
  4. A

    64 Ford 2000 Intermittent White Smoke and Pop from Exhaust

    My tractor starts/runs fine. Today it started every minute or so it will emit a puff of white smoke out of the exhaust and a light single pop. Good temp, oil pressure, otherwise no smoke out of the exhaust. What do you guys think?
  5. A

    Hydraulic Cylinder Rod Straightening

    A bit off topic, I managed to bend two hydraulic cylinder rods and the manufacturer wants an 2 arms for them. A fella on the interweb says he can straighten them to the 7 thou tolerence, and I found a shop that says he can do it. Anybody had any success with doing that?
  6. A

    Install new bumper, can't get the old bolts out

    Realized a prior owner just cut the bolts off flush front and back and they will not drive out with a punch and sledge. I don't want to mess with trying to drill them out, so plan is to heat up the axle around the bolt with a torch to break the rust to see if I can free them up. I also loosened...
  7. A

    Changing all 63 Ford 2000 4 cylinder Fluids

    Changing all fluids in my fairly new to me 2000. From researching post here, although lot's of different opinions, and calling my local New Holland dealership I am going to put Tractor Supply Travellers UTF in all 3 chambers, Trans, Hydraulic and Rear Diff. Anybody think that is not a wise thing...
  8. A

    Changing PTO Seal on 64 2000 4 Cyl

    Before I start taking stuff apart, I'm assuming all I need is a new seal and the gasket (4 bolts) on the PTO cover. Seems pretty simple. Any surprises I should know about?
  9. A

    64 Ford 2000 Fuel line routing

    Fellas - I am giving up on my interim fuel line as am not getting sufficient flow to carb to keep it running. I ve purchases a new fuel line and tank shutoff from here but cannot figure out how it routes. Would one of you please post a photo. I am assuming the line comes preformed but just get...
  10. A

    Newbie Question on 63 2000 Distributor

    New 2000 Owner here. Love this tractor. What is that little outlet under the distributor that had a little hinged cover over a 1/4" or so pipe?
  11. A

    OT 64 Ford 2000 4 Cyl Gas PTO Not working properly

    Fellas I hooked up my finish mower yesterday for the first time on this tractor and found that the PTO doesn't seem to work properly. I cannot engage the PTO by pushing in the trans clutch. I have to kill the tractor, engage PTO and start the tractor. Also when I engage the trans clutch, the...
  12. A

    64 Ford 2000 4 Cylinder Gas

    Hooked up my finish mower today to my new to me 2000 and noticed that I cannot engage the PTO by pushing in the clutch. I have to turn the tractor off, engage the PTO, then start the tractor and everthing work fine. However when I engage the clutch to shift into a different gear or stop the...
  13. A

    New Old Tractor Fleet - Quite a learning Experience

    My dad, also an old gearhead, recently gave me a 45 2N and a 63 2000 (Really an NAA). The 2N got a new fuel tank, fuel line, battery box, air filter, thermostat, hydraulic pump rebuild, all new fluids, carb rebuild, alternator, coil points and condenser, and a special inline ammeter on the coil...
  14. A

    Internally resisted N coils - Myth or reality ?

    Just received my new coils after a failure of mine with a crack top to bottom on my 45 2N. Naturally was concerned excessive heat caused the failure. Bought a $30 internally resisted coil from Styner and and $15 coil from YT. I only have a p/n 12250 resistor mounted near the dash between the...
  15. A

    Slight surging in my 45 2N

    Just replaced coil/points/condenser/dist cap took the dist off and apart and cleaned magnets. Put it all back together and went for a drive. It starts right up, idles smooth but running around on the road in 3rd gear at max rpm it seems to have a slight surge. Doesn't appear to be the engine...
  16. A

    Oil Seeping out of Steering Box Housing - 64 4 Cyl 2000

    Is it common for a pretty good leak where the steering gear housing attaches to the frame?
  17. A

    Ideas for latching my NAA style Hood

    The hinges are gone on my hood. Don't want to buy a new hood yet. You guys have any clever ideas for keeping that thing from rattling around?
  18. A

    LIft Position Lever Lowers Itself on 64 Prior 2000

    Plowed the arena yesterday with my new Prior 2000. Guessing it was the first time she was put to work in a long time. Noticed that the lift position level would lower itself when the plow would take a deeper bite. I had the control knob in the position control vs. draft control location. The...
  19. A

    Has anyone seen a detaileddescription of how a MS Carb works

    Attempting to adjust the carb on my new prior 2000, found the initial settings in the shop manual as to initial settings and we will get it figured out as we did on my 2N. Got the tank and carb all cleaned out today, and will eventually put a carb kit in it. As I was adjusting the carb today...
  20. A

    Help ID my new old tractor

    Hey N guys, would you please take a look at my post over in the Ford forum. Where I’ve got some pics and what I’ve found on the net. Hoping you guys can confirm what you see vs what the engine codes indicate. It does have a 5 speed Live pto. Would post a link but am on my phone.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top