(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. G

    1020 Rockshaft Hydraulic Issues

    Trying to go through and get my 3pt to behave like it should and am needing some help. I am having issues with the 3pt lift being very weak not being able to lift more than a few hundred pounds, as well as it not lowering all the way. I have been going through the steps in the tech manual on...
  2. G

    1020 Clutch Replacement

    I'm looking to replace the clutch in my '66 1020 Gas here pretty soon. I'm good with a wrench, but have never split a tractor before so this will be my first time. I have the shop manual, and will be looking to building me a set of splitting stands here in the next week or so. Tractor does have...
  3. G

    1020 Rear Engine Oil Seal Replacement

    Howdy, The rear engine oil seal on my 1020 gas is leaking pretty bad and in need of replacement. While I'm at it I plan on putting in a new clutch. Aside from splitting the tractor what is involved with replacing this seal? The service manual goes over this but it's with the engine on a stand...
  4. G

    1020 Runs Inconsistently

    Got a '66 1020 gas using it to mow. It fires up right away and runs like a top for 30-40 minutes and then it begins to sputter. It will start off as just a slight sputter and then gradually get worse until it's constant and wants to die. I shut it off and it is very hard to start again if it...
  5. G

    1020 Carburetor Problems

    I'm attempting to rebuild the original marvel schebler carburetor on my 1020 right now and have run into a couple issues. The fuel bowl was leaking badly and it idled badly and was extremely dirty which is the reason for the rebuild. I've rebuilt the carb recently for an 8n and they are fairly...
  6. G

    1020 Control Arm Shaft Leak

    Howdy, I'm working on my 1020 going through and fixing the various leaks. I have searched and read several of the post about fixing the o-rings/seals on the draft control arms, but have one question. I know that once you replace the seals that any play needs to be shimmed out on the shaft. On...
  7. G

    1020 Mower Size

    Well I decided to bite the bullet and buy a 1020 tractor recently. It's in decent shape, has some leaks nothing that I cant fix in due time, but great paint and tin. Now I am in search of a brush hog mower. What size mower will this tractor run? Will it run a 6 footer well, or do I need to stick...
  8. G

    Cant Decide on tractor

    Howdy, we recently bought some property 14 ac and I am looking to get a tractor to do some mowing, driveway grading, and fence building. I thought for a while I'd just go buy an 8n due to how cheap and plentiful they are, but then I stumbled upon a couple of JD 1020's for sale in the $4500...
  9. G

    8N 3PT Arms Don't Go all the way down

    Howdy, I have a '49 8n that I've been working on lately. I recently took the handle off of the hydraulic lift control to put a new cork friction gasket behind it. It needed a little heat and some prying but I got it off, replaced the cork, and put it back together. Now it seems like the arms...
  10. G

    Axle Trumpet Studs

    Does anybody know where I can find some new mounting studs for bolting on the rear axle trumpet? I messed up the threads on one and need to replace it. I realize I can just use a 7/16" bolt but studs are generally stronger than a coarse thread bolt. I've looked on here, nnalert, and mcmaster...
  11. G

    8n Crankshaft Pulley Loose

    Howdy, '49 8n front distr...While replacing some parts on the cooling system and replacing the belt, I noticed that the crank pulley was loose and wobbled. It has some front and back play as well as I can turn it back and forth about a 1/4". What is all involved with fixing this? I know I'm...
  12. G

    8n Engine Block Coolant Drain

    Howdy, first time posting here, but have been reading and looking around for a while. I got a '49 8n that I have been going through for a couple months as time permits. It sat for 2-3 years before I got it so have been doing all the typical maintenance, rewire, plugs, distributor, fluid changes...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top