(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. D

    1945 B first reduction gear outer bearing part number

    Can't find the part number for this bearing. Anyone have it or a new equivalent part number? Thanks.
  2. D

    AB403R Unstyled B hood

    Apparently the aftermarket hoods that were being manufactured are no longer being produced. Mine is probably too far gone to save, especially for the price of the bodywork vs buying a new replacement. Does anyone know where I can still get a replacement new manufactured hood? My tractor is a 1936 B.
  3. D

    1945 Deere B Flywheel end play

    Does setting the crankshaft end play on a 1945 B require removing the dome shaped piece on the outside of the flywheel that has the dogs for a hand starter? If so I cant seem to figure out how it comes off. It is held on by 2 bolts and even when those are removed it wont budge. Can I just loosen...
  4. D

    Deere 2 cylinder studs?

    I am swapping blocks on my 45 B with a bored block, and had to swap studs over. I see many go into the water jacket. I assume putting liquid Teflon on them wouldn't hurt anything, but from what I can find it isn't needed other than certain studs in the head for the manifold. All the block studs...
  5. D

    Unstyled A transmission gear noise

    To all those with a 34-38 Deere A. How noisy is your transmission? I have a number of classic tractors and I am concerned about the amount of gear noise from my 36 A. While pulling the drive side of the gears is pretty significantly noisy. Of ccourse when coasting or with no load it goes nearly...
  6. D

    1936 Deere A popping out of L range

    Just got a fully restored 1936 Deere A and did the fan conversion. Was really looking forward to putting her to work. Problem is when I pull a moderate load it is popping out of L range in 1st and 2nd gear. Is there an adjustment for this or will it require parts replacement. The detents and...
  7. D

    John Deere A Fanshaft Conversion

    Can you just remove the rubber fan, insert the required shaft spacer and reassemble with the friction fan parts, or do you have to remove all the rubber fan parts on the radiator end of the shaft and install new friction parts like washers, bearings and the new felt with retainer? I have a 36...
  8. D

    Unstyled front hood bolts

    I need to remove the hoods on my 36B and 37A. Damn bolts are spinning and there is no way to hold the carriage bolt head. How the heck does one get these things out?
  9. D

    Discouraged

    I have collected a few Deere's throughout the years including a 1936 B, 1937 A, 1939 H, and a 1945 B. All in various states of brokenness. I am not brand loyal, as I have several a Case SC's and a couple Farmalls. I have a great amount of mechanical aptitude and a machine shop with a lathe and...
  10. D

    1945 B with freeze damage

    Got a good deal on a fully restored 1945 B with electric start, lights and new rubber. Poor guy I got it from rebuilt it and painted every part before reassembly, then parked it in an insulated but unheated garage forgetting it still only had distilled water in it. He came out in the spring to...
  11. D

    271 Hayliner rear door?

    Just bought my first baler to go with my antique tractors. It is a New Holland 271 Hayliner. The sheetmetal is all nice and straight, and it is a good candidate for restoration. Only issue is it is missing the door on the rear of the hay carriage (where the fingers push the hay into the bale...
  12. D

    Anyone tired of replacing tractor/vehicle/mower batterie

    I have been playing with graphine ultracapacitors for a few years now after watching all of lasersaber's videos on YouTube. Turns out that for specific niche uses that ultracapacitor "batteries" are fantastic. I have a pair of 6 cell units that I put together using Maxwell boostcaps for one and...
  13. D

    Cast iron seasoning (manifold)

    As a lover of classic cast iron cook wear I am very familiar with seasoning techniques. I wondered if it would work on a tractor exhaust manifold, so I went to work on my Case SC with my Flaxseed oil and a paintbrush. Light coats, wipe off all excess with a lint free rag (until it looks dry)...
  14. D

    Case SC Battery Draw

    I just rebuilt my generator with a kit off ebay (super easy to do), and replaced the regulator with a NOS Delco-Remy D-647 (hate chinese junk). https://www.ebay.com/itm/325544444066. I replaced the wires in the same order that I took them off the old regulator (battery in the middle, arm and...
  15. D

    Case SC implements in SE Nebraska

    Anyone reasonably close to SE Nebraska and have any implements for a Case SC lying around? Specifically looking for mounted cultivators and any other unique implements for this tractor series. I do hobby farming and would like to utilize the tractor for its intended use. Could also use a...
  16. D

    Canopy on vintage tractors

    It gets hot here in Southeast Nebraska, and I want to put a canopy or umbrella on some of my old tractors. Two factors to this, it gets windy here, and I don't want it to look stupid. My tractors are as follows, 47 and 52 Case SC's, 39 John Deere H, 36 B, 37A, 35 Farmall F12. All have the...
  17. D

    52 Case SC Eagle Hitch Cylinder rebuild

    My manuals are too old to show the eagle hitch parts. What are the part numbers for the hydraulic cylinder seals?
  18. D

    What did "original paint" really look like?

    We all know what tractor show tractors with high gloss automotive paint look like, and sure it's nice for a showpiece. What did the original paint on a 30's-50's JD, Case, Farmall etc really look like? I assume they were just sprayed quick with primer then a couple coats of a semi gloss paint...
  19. D

    Hand clutch engaged or disengaged while idling?

    I assume that the Case is like a Deere. Engage the clutch in neutral while idling instead of leaving it disengaged, correct? Didn't see anything in the manual about this.
  20. D

    Case SC narrow front adjustment/rebuild

    I have play side to side and up and down in the front pedestal of my 52 (narrow front with 2 wheels) Case SC. Unfortunately the parts manual I have lacks exploded view diagrams. I have replaced the annular bearing in my John Deere H lower pedestal, and was wondering if a similar bearing for the...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top