(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. T

    C Countershaft Nut, Ring and Pinion Questions

    On a C I'm having troubles getting the ring and pinion set right. My problem is, when I tighten down the countershaft nut, it pulls the pinion gear out too far to properly mesh with the bevel gear. I've taken all the shims out and it's still set out too far. When I took it apart, the...
  2. T

    C Countershaft Nut Torque

    Is there a torque spec for the countershaft nut on a C transmission? I can"t seem to find anything on it. Thanks,
  3. T

    C Pinion Settings

    I've been trying to check the gear mesh patterns between the pinion gear and bevel gear on my C. Once I got it about right, I took the front cover off the counter-shaft nut and found that the shaft had worked itself out about an 1/8th inch. What's going on here? I replaced all the bearings on...
  4. T

    C Differential Bearing Preload

    I've been going through the transmission and differential of my C and replaced the differential bearings. I put it back together with the original shims and it's pretty tight. Should new roller bearings be preloaded? Is there a spec? Couldn't find much in my manual. Thanks
  5. T

    1086 Harmonic Balancer Removal

    We're trying to pull the balancer off the 1086 and was wondering what's the best way to hold the engine from turning over when cranking down on the puller. Thanks
  6. T

    1086 Engine Labors When Steering

    I just replaced a hand pump on the 1086 with a reman. The old hand pump leaked internally and caused the steering to drift. With the new pump, I now noticed when sitting still and you turn the wheel to the left the engine slightly labors until you turn the wheel back to the right. Is something...
  7. T

    1086 Engine Labors When Steering

    I just replaced a hand pump on the 1086 with a reman. The old hand pump leaked internally and caused the steering to drift. With the new pump, I now noticed when sitting still and you turn the wheel to the left the engine slightly labors until you turn the wheel back to the right. Is something...
  8. T

    1086 Steering Drifts to the Left

    Our 1086 steering drifts to the left when running. In about 5 minutes of just sitting idling it will steer all the way left. The tractor steers fine, but it just drifts off to the left. Has anybody had this problem before? Thanks
  9. T

    Painting inside of castings?

    I"ve got the transmission case from our C Farmall all torn down and was wondering if the right type of paint is available to repaint the inside of the casting? The original paint is pretty good, but some has come off in places. Thanks
  10. T

    C Blue Ribbon Service Manual

    I'm looking for an IH Blue Ribbon Service Manual for a Farmall C. I found one for a Super C on this site, but was wondering if anybody knew where I could find one for a regular C or are they close enough it won't matter? Thanks
  11. T

    IH McCormick Deering Decals for '48 C

    I have a 1948 Farmall C, I was wondering if the correct decals are available, that have the IH Logo along with McCormick Deering above Farmall? Seems like everywhere I look has either ones that have the IH logo with just McCormick above Farmall or have no IH logo and have McCormick Deering...
  12. T

    C-295 Plow Mounting Brackets

    I recently purchased a C-295 plow for a Farmall C, however it is missing the mounting brackets that bolt to the torque tube and the rear lift that attaches to the rear axle. Does anybody have any ideas as to where I might be able to find these parts? I"ve also been thinking about building them...
  13. T

    C Plow Question

    Can anybody tell me which plow this is? I"m thinking it"s either a C-294 or C-295, but I"m not sure. Thanks pic 2
  14. T

    C and Super C Rear Frame Interchangability

    I found a few old posts about the differences between the C and Super C rear frames, but never any conclusions. Will the rear frame from a Super C work on C? I know it will bolt up just fine, but what"s different? Brake mounting holes? Anything internally that I should be aware of? Thanks
  15. T

    F3 Curtain Over Raddle

    Should the curtain over the raddle chain be in place while running corn or soybeans? I can't find anything about it in the manual. Thanks
  16. T

    Gleaner F3 Unload Auger

    I"m having a problem with the unloading auger folding out on our 1983 Gleaner F3. It works fine the for about the first hour or so the combine has been ran, but as the day goes on and the machine gets warmed up, the auger doesn"t want to fold out as it should. You have to press down on the...
  17. T

    IH 800 Planter Level Lift System

    The level lift system on our 8 row, pull type, 800 Cyclo planter with end transport doesn't work, and hasn't for a long time. I've been trying to figure it out but haven't found much information about the system. The manual says to replace the pressure switch and then the electronic module...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top