(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. I

    918 flex head

    No just the indicator on right side of header.works perfect when on ground.I don;t know what switches it to stabelize it when you lift it at the end.put a new circuit board in controle box at right side of header no difference.at a loss.
  2. I

    918 flex head

    i had the chain on my 7700 with 215 header but this one is different.
  3. I

    918 flex head

    918 flex head on9400 combine.When i am cutting soybeans and on flex and come to the headland and lift the head to turn around the heda will not stabelize but want to go back down without hitting the down button.I have replaced the header,reel button earlier this season.Everything seems to be...
  4. I

    4440 medallion question

    I have a 4040 original emblem it has writing
  5. I

    6420 deere 4 wheel drive

    Maybee poor conection or broken wire on celenoid,as was already said this clutch is powered to release clutch.
  6. I

    Advice Needed.

    4030 has both 540 and 1000 rpm pto.
  7. I

    JD 1530 clutch pedal suddenly hard to move

    There is a grease nipple on clutch shaft next to TO bearing.
  8. I

    Rear wiper for 4630

    I got one from JD a year ago.
  9. I

    Rear wiper

    Thank you
  10. I

    Rear wiper

    Instaling a rear wiper on 4040.No instructions with kit. Where does power source come from? Thank you in advance.
  11. I

    '78 2040 popping rear end

    Make shure diff,lock is not partually engaged.
  12. I

    Chevy 2500 can't get it out of gear

    If it has to be bled,get a clean pump oil can fill it with proper fluid and with a rubber hose atached to it and the bleader port bleed from the slave cylender to the resivor.It is the easiest way.
  13. I

    4020 Throttle Control Linkage adjustments

    Did you pull out the stop button on the throutle.Just a thaught.
  14. I

    Poll or old members

    Check every day.
  15. I

    Sqare baler ejector

    Did J D make a electric cab controler for the jd 327 baler ejector?
  16. I

    4430 hydraulics

    Some of the 30 series tractors didn^t have a designated valve to run a hyd motour.I think all 40 series and newer had.
  17. I

    What's it worth

    If it missed between balls it is likely tracks worn in needles and the knots are hanging up in needles.
  18. I

    Stop the spudpocalypse campaign

    IT IS A VERY BAD SITUATION.
  19. I

    Merry Christmas

    Merry Christmas from P E I Canada
  20. I

    4420 Engine Removal

    Check for sleeve cavitation.They were prone for that.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top