(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. H

    Allis Chalmers WD Water in Oil

    Ive flushed it out really good, dried the inside with mt heat gun on low, i poured a pint of aviation sealant in and and when its together ill use the bars and a secondary protection
  2. H

    Allis Chalmers WD Water in Oil

    it looked like the cylinder towards the fuel tank
  3. H

    Allis Chalmers WD Water in Oil

    I have 1952 WD, it had been getting water in the oil, I've ruled out the head gasket and freeze plugs in head, it seems like its getting around the o ring on the sleeves, minus this issue it starts and runs good, no smoke or bad sounds. I was reading that some will use aviation sealer around the...
  4. H

    Wd hydraulic pump help

    I have a 1952 allis chalmers wd, the hydraulic system was abandoned years ago, i am wanting to go through it and get it working again. I figured rebuilding the pump would be a good start but im having a heck of a time finding a rebuild kit for it! Does anyone have an leads on a rebuild kit?
  5. H

    Ford 2000 throttle not staying put!

    I have a 1970 ford 2000, the throttle will not stay put, it has been likely rigged and worked on long before me, ive installed a new friction disc and spring and still doesn't like to stay put. It almost seems that the governor is able to easily over power the throttle friction disc, any help is...
  6. H

    Ford 2000 clutch replacement advice needed

    Ok folks. I got my clutch kit in the mail. I have my flywheel resurfaced. I'm soon to be ready to put it back together. So the clutch has three adjusters in the center that ride on the throw out bearing I believe? They look poorly adjusted. None of them look even. How do I set that up? I also...
  7. H

    Is there a 2110 split in my future?

    I've just had the same issue with my 2000. Clutch was the issue.
  8. H

    Ford 2000 throttle lever help

    I have a 1970 ford 2000. The throttle lever has never stayed put. I've always had to hold.it or bungee cord it. It doesnt really have a friction disc, just some kind of rubber washer that doesnt work. Does anyone have a picture of what the setup should look like or maybe a homemade setup? I just...
  9. H

    Ford 2000 clutch replacement advice needed

    Ok guys! Ordered a clutch kit. I have a few questions. I dont have access to a manual. I need to know the torque values for the flywheel to the engine and clutch to the flywheel. Also does the clutch need adjustment of any kind before I put it together ? Thanks
  10. H

    Ford 2000 clutch replacement advice needed

    So it doesnt have to have the triangular disc? The triangular disc kit is the most expensive lol
  11. H

    Ford 2000 clutch replacement advice needed

    I have a 1970 ford 2000. It has the dual stage triangular clutch. It's completely shot. I've got my tractor split and have the clutch out. Where is the best place to get a clutch kit? I dont wanna do this job again. Also does anything need adjusted on the clutch when I install it? I seen it had...
  12. H

    Ford 2000 two stage clutch problems!

    Rebuilding seems like a good idea but I've never heard of rebuilding a clutch. Idk of any shops in my area.
  13. H

    Ford 2000 two stage clutch problems!

    Thanks all for the replies! Looks like a new clutch is what I need! I've never split a tractor before !! Also were is a good place to get a clutch kit ? Thanks
  14. H

    Ford 2000 two stage clutch problems!

    I have a 1970 ford 2000 gas. I've never been able to get the 2 stage clutch to work. So I tore it down far enough to get the steering tower off to adjust the clutch internally. This is what I found 2 of 3 adjusters are broke !! Is this repairable in the tractor or is it time for a...
  15. H

    Ford 2000 alternator conversion

    Thanks for the response. I think I may just order a kit. They are on sale on Ebay for about 120. I did not realize the tach would read fast!
  16. H

    Ford 2000 alternator conversion

    Thanks for information I will make sure to add engine info next time. I am wondering to how hard it will be to add the tach drive to the alternator. Has anyone added a tach drive to a run of the mill gm alternator?
  17. H

    Ford 2000 alternator conversion

    So after testing my charging system I determined I had a bad VR. I replaced it with a new one and still issues. I decided to go with a chevy alternator and do away with the generating system. I have a good alternator and I've found I can buy the tach drive from yesterdays tractor for 27$...
  18. H

    1970 Ford 2000 Not Charging

    I tried polarizing the generator no luck battery is still not charging. I tried checking output on the generator only got 2.9 volts seems like the generator is bad but idk.
  19. H

    1970 Ford 2000 Not Charging

    I will give it a try after work!
  20. H

    1970 Ford 2000 Not Charging

    I have determined my tractor is not charging, im getting 11.9 volts on the battery no matter what rpm. I need help in testing the generator, i seen it has a large and a small spade on it. If possible ide like to test the generator, i figure it has to be either the generator or voltage regulator...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top