Farmallb

Well-known Member
Looked again. The simulated tag says 82 - 86 the best I can see with a mag glass. & A-1140 R

The metal tag on the slanted pipe with cap on it on the hyd lift says PC 6534, But im positive this has been added on, as it has a hand rather than a foot acvator, and I dont think the hand lift came around till 46, and the holes for the foot lift would have been gone out of the casting. It also came with a JD 3 pt hitch, which also tells me that someone put the lift on it. They wanted to operate a 3 pt off of it.

Tires on both are 38s
A, wheel has 3 holes around 1 1/4dia around 5in from center with a slash cut through from hole to center. B wheel is triangulated in the center, with 9 holes in it, and 6 bolts holding it to the hub. BOTH tractors, the wheels can be removed from the hubs and the hubs left on the axle.

B has nuts holding on brake drums.
 
As I said before, the heat code doesn't jive with heat codes used at that time. Is it possible the number is 82-36? If so, the case is from a 36 model A.

Also as I've said before, the lift assembly (valve, rockshaft/rear cover housing) on the tractor may very well be original to the tractor. It is the lift valve body that has been changed to a Power-Trol valve body. You are right that the Power-Trol (just an upgraded version of the Powerlift) did not come out until 46, but from all that you have described you have a powerlift with a power-trol valve body on it. The powerlift/rockshaft housing has been around since well before 39, so yours could be original to the tractor. The tag you mention on the valve body, I don't recognize. Could just be an inventory tag or something like that. It has no meaning to me, and probably should be ignored for the purposes of determining an approximate time frame.

Lastly, once again, where was the tractor's serial number tag? Was it located on the left front "side" corner of the eng/trans maincase, or was it on the right front "top" corner of the maincase? This will roughly split the 39 model year in half.
 
Thanks for sticking with me.I put oil in it tonight and hope to start it off the belt tomorrow. U say a tag should have been on the L H side. I havnt seen it. The simulated tag pressed into the casting that you say dates back to 36, pressed into the side of the gear case

On the R h side in front of the pulley wheel.

Found out today I took some pics of it. Just gotta figure how to get them from photobucket into here. Thanks again
 
I'm gonna give this one more try.........

The serial number tag that was mounted on the model A at one time, like when it was new, was in two possible locations. This is in 1939 only.
I have described their locations in my response above. There should be evidence of the tag location still remaining, as I described in your previous posts.
At no point did I say that the casting dates back to 1936. What I said was, if the heat code is in fact 82-36, then the case was cast in 36. I'm relying on you to give me the correct numbers.
I have included pictures of the two locations of the tag, and one of the casting/heat code number as they might appear on a 39 A.


Your tractor does have a sheet metal grill covering the radiator, doesn't it?
 
One more try on the pics.
a62464.jpg

a62465.jpg

a62466.jpg
 
There is NO tag on top where you show the one on the green block. I cant tell where the tag is on the old block, I thought there was one in the vicinity of the flywheel, but there isnt one. On the other location. I looked hard as I thought it ought to be by the mag, BUT theres nothing. No pin studs or nothing. I see your numbers on the simulated tag, 94. Mine have 4 numbers seperated by a dash. Its easy to see.
 
I'm guessing when you say "old block" your talking about the one in the 2nd picture.
The picture of the tag on the "old block" is just where you thought. That picture is just ahead of the flywheel. The casting you see just above the tag is the base of the governor. The tag had to be in one of those two locations. Sometimes the rivets have been ground off, or sheared clean. They can still be seen if the metal is bare. Looks like a tiny star, the spiral of the rivet in cross section.

I'm going to send another couple of pictures. The first picture is of a portion of an unstyled maincase. It is taken in the same area on the tractor as the first picture from above, where the tag is located on a later 39 A. Notice how the "top" corner area of the maincase is "filled in" and machined flat on the 39 case but not on the unstyled case? Which one do you have?

The other picture is of a heat code from a 36 A that is pretty poorly cast. Has a lot of "sand" roughness from the molding process. Is it possible your 86 is actually a 36?

Again I ask about the grilles?
 
I have a grill. In my origional post, I acknowledged that it had to be an early 40s A, and I know that the last full year of the unstyled JDs was 38. My block is exactly like your last pic showing clutch pad holder.

Am I right, then, assumeing its a 39? If so, Is that a rarer tractor than from 40 on up, or about the same? Thanks again for the help and persistance.
 
Can u tell me what goes into the hole, that is threaded, Is part of the head casting, that is capped in the casting. It is beside, and L of the oblong open hole the choke rod goes through? It is around 1 1/4in dia, and around that deep, and is, as said, capped as made in the casting? It is just L of the fan shaft, where it ends up at the gear end, and around equal in highth of it. Thanks.
 
At this point it doesn't seem like you can assume anything.
I hope this doesn't get too confusing.

Your maincase is of the unstyled version of A1140R. This style of case was used from the beginning of the 36 model year (unstyled) through about mid 39 model year (styled). Maybe about Feb 39 at around 482000/483000. If anyone reading this has one in that serial number area, I would be interested to hear from you.

The problem is your heat code. It is impossible for the second number to be an 86, based on all known information about heat codes being used at that time. The second number used on unstyled heat codes is the production year.

IF your heat code is 82-36 instead of 82-86 as you have indicated, then your case was indeed cast in 1936. Being cast maybe about mid Feb 36.
IF this is the case (no pun intended), then it appears you have a morphodite tractor, made from more than one.
IF the code is truly 82-86, then it is still an unstyled version of a heat code number, that may have an error, and was cast prior to about June of 38.
IF this is the case (ditto), then it appears you have a morphodite tractor, made from more than one.

IF either of these cases are true, then you have to decide which half of the tractor is the most important half, and I guess start calling it that year model. Bottom line is to enjoy the tractor, and learn from the experience and knowledge gained.

It's entirely possible the steering pedestal and or front frame are from any tractor up to 47. A styled frame is longer than an ustyled, so that probably could be determined for sure.

1939 is not a rare model, they made about 9300 of them.
 
You really need a parts book, so you know what to call the different parts you are asking about. You can download a PDF file of the parts books online from Deere, for free. If you need help getting that done, please post new to inquire about it.
I'm just having a hard time deciphering your descriptions. I think you might be talking about the shutter control knob/threaded hole. Not sure.
 
I forgot to mention. The hole faces towards the engine. DIRECTLY behind the capped end of the hole is the pin or stud, that holds the metal piece, that holds the rod going to the carb, AND the tin piece going to the rod going to the gas lever. The hole is built into the casting below it, and has the open bolong hole beside it to the R that the choke rod goes through and maybe the rod going to the carb.
 
Go back and read all his posts. He wants to get to the DAY his tractor was made. And has no pictures or logical way to explain himself. If it wasn't so entertaining I skip his posts, but he has no idea of what he is looking at or how to describe it. The day part was sarcasm, I think. With his clues we have narrowed it down to a couple years but he keeps coming back.
 
I can only guess that you are talking about the ventilator tube packing gland hole on the top of the governor housing. That hole is nowhere near 1 1/4".
Get a parts book, and a tape measure.........please.
 
wow........no kidding. I want to help, and get to the bottom of what he's got. I love a challenge.......but it's supposed to be the tractor that gives the challenge.
 
Well since its a 39 likely, and yet has the marking on the simulated tag that could take part of it back to 36, I think thats something id like to show if I take it to shows.

U right. I aint no machanic. Never wanted to be. Im just retired, and I wanted one of these before they was all gone. I cant buy the best on retirement, so I gotta work with what I got.

Ive farmed all my life. Dad had a 40 A or B in the early 50s, a 38 A in the late 50s , a 49 A and a 50 B in the EARLY 60s. I grew up farming at home with JD tractors. I just want one to hear it, besides the work it will do on my farm.
 
Farmallb, you may be chasing the impossible dream. After 60 or 70 years noone knows how these tractors have been "farmerized" or repaired with the parts available at the time. May not have been the right part but it was what was at hand. Seen regulars with f-20 manifolds, flambeau cases with distributors instead if mags, all fuel deeres with gas manifolds. Unless the machine has been in the same family and the history can be verified one should not sweat the small stuff and enjoy them for what they are
 
I would highly recommend a decent digital camera so you can upload some pics. Sometimes it's just a lot easier than trying to describe something. I think it would help everyone.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top