Brush hog U-joint zerk

The U-joint zerk at the rear of the drive line where it connects to my Woods Brush Hog is really tough to get at. There is a quarter-sized hole in the drive line shield, but I have to at least partially remove the drive line shield to get decent access. It"s an angled zerk, but it seems near impossible to connect to it, as the U-joint is pretty much in the way. But I do manage to do it every year. This year I had to loosen the zerk and turn it some to get decent access, I haven"t had to resort to doing that previously.
The U-joint zerk on the front end of the drive line (closest to the tractor) is easy to get at.
Anybody have any suggestion for making this easier ?
How many operating hours is a grease job good for on the U-joint ?
 
I'm anxiously awaiting answers/solutions as you get responses..My First Choice finish mower is like that also. Have to loosen the fitting to even think about getting on it..Most aggravating thing I have ever had to deal with.Like greasing anything isn't pain enough without other complications.....all other grease fittings are well engineered and thought out-easy to access. Actually not a brand specific problem, just a painful thing on any U-joint I guess....
 
Charlie:

U-joints do not need much grease. It will be fine if you manage to grease it well once per year.

Dean
 
Charlie......you do know Zerks come in different sizes and angles don't you??? 0*, 45*, 90*, they also have different thread sizes, so take yers in for a sample. They are replaceable, go shopping. Simple, eh? ......respectfully, Dell
 
sure, I think this one is 45 degrees, but where it is located I don't think any angle will help.
As I said, the one at the front of the drive line is easy, I would think the one in the rear ought to be the same, but it is NOT, it is too obstructed, have to wrestle with it.
I have multiple grease gun adapters too, angled, plus the rubber tube extension one, no help.

I will say, after that task is done, changing the oil is a pleasant chore.
 
well I will have to look at it and puzzle over that idea.
Like the time I replaced the side steps. The wife got home and said "Honey, they don't look right". I had the stringers backwards, so the steps were REALLY NARROW, and the steps were REALLY FAR APART.
 
Charlie, they make a NEEDLE POINT for the end of your grease gun....it replaces the regular fitting. You reach it in and firmly depress the check ball in the zerk... then give it a shot or two. It isn't too fussy on the angle and when you're working in *tight* quarters, can be slicker than snot.

Ask NAPA or maybe even your SnapOn man.. I have even made one by hand...

If you find them, get the longest one you can. Pretty slick!!

duey
 
YES, I ** HAVE ** tried that :) And from both sides, plus including lying on top of the brush hog :)

I am going to pursue Duey's suggestion of the needlepoint adapter.

Honestly, I was hoping someone would chime in with "hey, they only need to be done every THREE years" :)
By the way, depending on how much rain we get, I only get in between 20 and 40 hours a year with the brush hog.
 
Charlie.......is there summ law that prevents you from enlarging that quarter sized access hole in yer plastic U-Joint shield for better access to yer greese fitting??? Just a thought .......Dell
 
The manual for my Woods Bushbull 60" rotary cutter says to grease the driveline slip joints every eight operating hours. If I recall correctly I had to disconnect the shield to get to the rear grease fitting. It also says to lower cutter to the ground, disconnect driveline from tractor PTO shaft,and slide halves apart but do not disconnect from each other. Apply a bead of grease completely around male half where it meets female half. Slide drive halves over each other several times to distribute grease.
HTH,
Mike OH
 
i always set mine on a old tractor rear tire to keep it off the ground, before i hook it up to the tractor, i pull the driveshaft all the way to one side making sure that the grease fitting is towards the open side , i wallowed the hole in the driveshaft cover out a long time ago, works pretty good, i grease it before each use,driveshaft and tail wheel zerks, and i probably use it about 20 hours a month in the summer
 
Yes, I do that too, but thanks for the reminder. I skipped that part of it yesterday as in previous years it seemed to still have plenty of grease there.
 

Toyota use to supply a nice adapter,,, it came in the tire changing tool kit for git'n at the grease fit'ns for the front drive shaft on their 4X4 pic ups,,, know any one with a toy 4 by,,,, the work'n end of your grease gun can B brought and you can grind away for a nice fit,,, no reason to fight a loose end,,, it should lock on the zerk,,, keep it clean and free of dirt
 
Even though the manual says every eight hours, I think that is overkill. As far as the joints go I grease mine once at the beginning of the season and maybe mid season, but mine doesn't get used all that often during the mowing season. Besides, I hate to have to remove the sleeve to get to the zerk at the gearbox. I learned quickly to wipe off the excess grease or I find it slung all over the mower deck and anything close by if I don't. As far as the center section goes, as long as it moves freely and I see grease when separated, I leave it alone.
 
They make an adapter for your GG that lets you use it as right angle, but as a slide on from the edge..

soundguy
 
i ave found that if i disconnect the drive line from the tractor you can twist the driveline around to gain better angles to grease the u-joints.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top