(800) 853-2651
SHOP NOW

Recent content by 300 dave

Yesterday's Tractor Forums
  1. 3

    SOLEX carburetor on 3444 loader back hoe ??

    I have posted this in the back hoe forum -no response, so... My 3444 has a SOLEX carb on it. I have never heard of this. They are a very common carb on European cars. Has anyone ever seen this ? Minimally I need a rebuild kit as I think it is plugged up with sludge. I don't want to tear it...
  2. 3

    IH 3444 carb ??

    My machine has a SOLEX carb on it. Could that be correct for an IH backhoe ? I know they are stock on old air cooled VW's , Porsche's, Mercedes, etc. It needs a tear down and cleaning. When I look for a gasket kit, the pic's of the main gasket are no-way going to fit/replace my unit. If I...
  3. 3

    I H. 3444 fuel issues

    yes -just as you said -it was loaded with sludge. there is a built n magnet which captured a pile of crap. there is a lot of crap coming out the top, high pressure side. I guess I will just have to run it to flush it out. How to do a pressure test? I don't think I have anything to test that...
  4. 3

    I H. 3444 fuel issues

    Hello all, The above pic is of my fuel pump on a 3444 backhoe/loader i got. Two pics as the pic was on m,y phone and is easy to load. I will not try to type on a phone. Fuel tank is loaded with black chunky stuff which clogs everything. I am working on draining- flushing it out. The pump...
  5. 3

    I H. 3444 fuel issues

    This is the fuel pump- can it be taken apart and cleaned?
  6. 3

    300 U hydraulic DEAD ?

    oh yeah I had forgotten about that !!! what a ROYAL P.I.T.A. to pull that and check it. My fluid is not milky just like creamed coffee. There should be no crap in the system ( from where?), I have pulled it and cleaned it twice. Can that screen be back flushed with air pressure?
  7. 3

    300 U hydraulic DEAD ?

    tractor runs like a top Starts up quickly, runs dependable -maybe a tad slow on the governor maintaining rpm-but nothing to complain about. BUT, every once in awhile there is a screeching sound and the engine bogs down and it is gone. It has done this for about 15 years I've had this machine...
  8. 3

    300 U hydraulic DEAD ?

    Greetings all - My 300 U hydraulic system does not seem to be working at all. I raise the handle to lift, and generally nothing happens. Once in a while it will lift the draw bar. I looked in the tank under the seat and see no movement of fluid at all (peeking in through fill hole). Over...
  9. 3

    2pt-3pt conversion ? on 300 U

    Mark Robke thanks I will work on that (pics) may not get to it tomorrow tusday. I have wonder about that geometry of the lift given the wide variety of attachments
  10. 3

    2pt-3pt conversion ? on 300 U

    all you need is an anchor for the top link. I have the top part on the machine - rock shaft ? for toplink hookup. All the equipment have toplink hitch point as well. so I think I'm good to go is this maybe better? its cheaper
  11. 3

    2pt-3pt conversion ? on 300 U

    all you need is an anchor for the top link. I have the top part on the machine - rock shaft ? for toplink hookup. All the equipment have toplink hitch point as well. so I think I'm good to go
  12. 3

    2pt-3pt conversion ? on 300 U

    yes I saw some similar to those. price was about double that. those would sure work. thanks
  13. 3

    2pt-3pt conversion ? on 300 U

    Cub149 -- YES That is similar to what I was thinking about making/modifying. I was thinking of a bolt across the top to close the hole. I can weld one up. Great minds think alike. Anyplace I could buy something like those?
  14. 3

    2pt-3pt conversion ? on 300 U

    thanks D Red. I think the whole "fast hitch" thing is a myth. Mt two bottom plow will "fast hitch" if all is on hard dead level ground. Otherwise it don't line up and requires a couple trips on and off the machine to get it on. Same with the 2pt adpt prongs. Unless in the sockets they flop...
  15. 3

    2pt-3pt conversion ? on 300 U

    On my 300 U I have the 2pt fast hitch.and the 3pt conversion for top link. I have a couple sets of 3pt adapters that go in the 2pt sockets. Problem is the the 2pt "Y" frame is rigid and will not allow flex to hook up 3pt stuff. For example a simple flat draw bar can't be mounted unless I pull...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top