(800) 853-2651
SHOP NOW

Recent content by B n 60

Yesterday's Tractor Forums
  1. B

    JD 60 clutch

    The grooves will go up against either the sliding drive disk or fixed drive disk. That"s where the main wear is going to take place.
  2. B

    B with an A carb (Please look B-maniac)

    It appears I finally got the carb in tune last night... I went back and did the two no-wrench tests again and after it was all said and done, turns ended up being about 1 1/2 idle and 3/4 load (just like you had thought Pat). Only time it smokes a bit is when I take off from a stand-still...
  3. B

    B with an A carb (Please look B-maniac)

    Thanks guys for the insight. Just read that carb article and looked at the 'no-wrench' tests at the bottom. I've essentially already done them, and it does run great at a slow idle (and fast) with the load needle shut. The problem comes when that load needle is opened up and it wants to take...
  4. B

    Farmall Regular price

    Just looking for opinions on what a fully restored farmall regular might be worth. Owner believes it to be a 1930.
  5. B

    B with an A carb (Please look B-maniac)

    As a refresher, I have a 44 B (with the newer B block) that has a A carb (dltx71) on it. Trying to get the needle adjustments right. When I have the load needle shut, and open the idle needle 2 turns (like you recommended, b-manic) it runs great just idling. However, when I then open the load...
  6. B

    B with an A carb

    b-maniac, do you know roughly how many turns your idle and load needles are? i"m having a hard time getting mine tuned it.
  7. B

    720 Lower Transmission Shaft, how does it come out??

    download the parts manual from the JD website and it might give you a better understanding of how that shaft is assembled
  8. B

    B with an A carb

    It has the bigger block on it (the one that originally was on the 201000 and up). Will try those settings. Thanks.
  9. B

    B with an A carb

    Have a 44 B handstart. The person who had it before me put the newer bigger block on and I guess decided it would be a good idea to put an A carb on instead of the dltx 67 it should have had. The carb had just been rebuilt and I just honed the clyinders and the valves look good, but when it...
  10. B

    Clutch cover '60'

    When you put the new rivets in to hold the new clips in place remember to buck em up good on the back. I've gotten the clips from JD a few years back, would be suprised if they wouldn't have them.
  11. B

    60JD Stalling under load

    Rule of thumb I always heard was 1.25-1.5 turns from bottom on load adjustment...
  12. B

    Power steering required for wide front?

    Also, is power steering required to turn a narrow front into a wide?
  13. B

    60 roll-o-matic

    I have a 60 narrow front that i'd like to put a roll-o-matic on. Can anyone tell me what all it'd take to do this job? I'd imagine it couldn't be all to difficult... do i just have to buy the spindle?
  14. B

    44 jd B brakes

    thanks. i got it out last night. turns out the gears were so badly worn that they actually got pressed out to a larger diameter and barely squeezed out through the housing. going to have to shave a little bit of them off before throwing her back in...
  15. B

    44 jd B brakes

    One of my bakes on a 44 B is froze and I am having a heck of a time trying to the assembly out. I can pull it out about 2.5" and then it seems to get hung up on something. Anyone have any tips/ideas on how to get it out? The break spins freely when it"s out, so I"m pretty sure its not getting...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top