(800) 853-2651
SHOP NOW

Recent content by bob from ill

Yesterday's Tractor Forums
  1. B

    190 ring gear

    got the rear wheels off and platform off. pulled top off rear diff. and removed lift arm housing. the diff only has 2 pinion gears,not been upgraded to 4. there is just a slight amount of lash between them. what is the limit as far as how much is acceptable? will be pressing out axles in the...
  2. B

    190 ring gear

    just wondering if the tractor has to be split, or can the ring and pinion be replaced thru the top and back end.
  3. B

    caterpillar diesel question

    I know its not a farmall but i dont know where to turn and you guys know everything about everything. Ive got a 955H trackscavator. it runs real good but suddenly it developed a miss under load. It runs smooth until it is working then it suddenly starts to miss like its fouling an injector. the...
  4. B

    Allis 500 loader

    I have a 170 with a 500 loader and everything Ive read and heard around states that there is enough adjustment on the extensions that go to the rear axle to fit 170 to 200 tractors. Also pretty sure it will fit the D17 and D19 too.
  5. B

    469 sickle setting

    ya its gettin cool here, but need the hay for the winter. ive had this mower for about ten years and have just figured it was just wore out and that my fields were the reasons it was doign the things ive mentioned. I was hoping to find a location to download or at least view pages from the...
  6. B

    469 sickle setting

    Hi. Just wondering if the sickles are to ride against the bottom of the gaurds. if they are, how do i make this possible. do i remove shims so the holddowns are tight against the top of the sickle sections. or can the guards be bent up to make them tight against the bottom of the sections. I...
  7. B

    d17 motor stumbles

    I have a 170 and it runs smooth so wednesday im gonna swap plugs wires and even the carb and see if it changes the way the d17 runs. When I say it stumbles I mean when at a set rpm itruns smooth for about 3 to 5 seconds then it just pops a small pop out of the exhaust pipe. i have a rain cap on...
  8. B

    d17 motor stumbles

    Ive read on here that lead additive is nothing but a gimick. ive also changed to a differant set of plugs with no change.
  9. B

    d17 motor stumbles

    freshly built motor runs descent. but it stumbles at all throttle possitions. rebuilt carb, new itake gaskets. new coil points wires and plugs(autolite 64 with 3/4" reach gapped 25 thous.) timed with light @ 25 deg btdc. When fist got running, it ran really smooth. the rain cap on the muffler...
  10. B

    gen to alt

    forgot to mention. its a first generation d17 gas tractor
  11. B

    gen to alt

    just wondering what would need to be done if even possible to be able to convert from generator to single wire delco alternator. also remember its a positve ground system so it may not be able to be done at all.
  12. B

    d17 rebuilt motor

    I found the problem. The rockers were a bit tight and letting valves seat. it was running low compression. Adjusted valves and now it absolutly sounds like a new tractor. Wow
  13. B

    d17 rebuilt motor

    newly rebuilt motor. pistons sleeves bearings and all new head parts. just got her running and its real nice. the motor does have a slight lope at idle though. throttle response is crisp with no sputter anywhere thru the rpm range. just wondering if they all have the "lope", or do i have carb or...
  14. B

    806 pto leaks

    the origanal housing had a crack by bolt flange and was seaping oil out for a few years. finally decided to repair. tried to weld crack but kept shrinking and a crack would form again. anyways, got a used replacement btu it had the seals removed already. I was able to press out my seals, there...
  15. B

    826 Screeching Brakes

    I just had my right side brakes apart on my 806 yesterday. The return springs were compressed and packed with brake dust. this wouldnt force the piston back in so it wore the pads out. just take the brakes off but leave the plate with the piston on the tractor, dont bleed fluid out of line...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top