(800) 853-2651
SHOP NOW

Recent content by Grandpa's 8N

Yesterday's Tractor Forums
  1. G

    Battery cable size Farmall H

    What size was the negative battery cable on a 41 H from the factory. Both off of the battery and the one going to the starter.
  2. G

    Farmall H won't roll

    41 H, split and new clutch. Pulled transmission cover pulled rear axles as gaskets were leaking. New axle seals and gaskets and pto seals. With tranmission cover off, everything rolled free. Have cover on, and tractor back together and tried to roll and it won"t roll. Brakes are adjusted...
  3. G

    Rear axle seal

    My parts breakdown shows a metal washer between the nut and hub and a cork gasket by the seal. I don"t have a cork gasket by the nut. Are you sure there should be one there?
  4. G

    Rear axle seal

    My parts breakdown shows a metal washer between the nut and hub and a cork gasket by the seal. I don"t have a cork gasket by the nut. Are you sure there should be one there?
  5. G

    1650 hydraulics

    The oil is not leaking between the coupler and the tip. I push the tip in and have an open hose- nothing on the other end- and oil comes out the hose. I have hydraulic pressure to extend and retract cylinders and loads just fine, but it is a pain to connect hoses- it can"t be done with tractor...
  6. G

    Rear axle seal

    The right hand hub is leaking oil. The leak all appears to be to the outside, no oil appears on the inside of the rim. Is this just he outer axle seal?
  7. G

    1650 hydraulics

    I have 2 remotes on my tractor. Both remotes build pressure up on the coupler while the tractor is running. If I take a male tip and a hose and insert it into the coupler, a small stream of oil comes out of the hose without moving the remote lever. It is the electro? hydraulics- There is a...
  8. G

    1610 loader

    I have a 1610 loader on a 1650. The lh main bracket that goes from the rear axle forward to the side rail is bent upwards. Bought the loader used and everything looked okay, but it wasn"t on a tractor. Any suggestions as how to pull it down to get the bucket level. The bucket is off 2 plus...
  9. G

    1650 steering tilt

    The rod going from the pedal up to the retaining pin broke, leaving no way to tilt the steering wheel up or down. Luckily it broke in such a position that I can use the tractor and get on and off of it easily. I have felt around trying to figure out how to replace the linkage. The only thing...
  10. G

    Video of 8N Blowing Snow

    I live just west of Nebraska City, by the big metropolis of Dunbar. Always wondered how close I was to Hec, getting closer all of the time.
  11. G

    1650 pto shaft oil leak

    1650, single speed pto. There is oil leaking onto the drawbar from the output shaft. The oil appears to be leaking from between the bearing and housing- so that is the oring. The pto has not been run for a while, but it also appears that the inner bearing ring/race is also wet. There is no...
  12. G

    8N Brake Finally

    Interesting thought about the splines not being true on the old shaft. I will have to check that out. Thanks for the idea.
  13. G

    8N Brake Finally

    I understand the splines wore on the shaft, but the hub was tight on the shaft- not sloppy. So by putting the new axle in, it slid the hub out, which is fastened to the brake drum, which moved the brake drum out which is the exact same thing the washers did to the brake drum slid it out- I...
  14. G

    8N Brake Finally

    After making several post on here about the brake locking up. I finally put a new axle on the right side and that fixed my brake issue. I used the same hub ( which had been replaced). I had even put washers behind the brake drum (tried a couple of these also) to space it out farther, but it...
  15. G

    Hydraulic snow blower

    Homework. Exactly what I am trying to do here J.S.. I figured if anyone had done it or tried it, it would help me out. Don"t have a clue as to hp to torque conversion. Can you help me with that J.S.? Ran it with a 660 oliver and it had plenty of power to run the blower and it is rated at 41 hp...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top