(800) 853-2651
SHOP NOW

Recent content by jhb

Yesterday's Tractor Forums
  1. J

    wd45 turbo

    test
  2. J

    1943 Farmall M wanted

    I know that the classified is the place to be but my wanted ad has been blocked 2 days in a row. WANTED: Formerly my fathers Farmall M, 1943,sold at auction in about 1980 in Dubuque, Iowa. My deceased father was Elmer Bradley of Dubuque, Iowa. The tractor was sold to Nick Merfeld who also is...
  3. J

    Farmall H missing

    Thanks to this forum and those that commented when I inquired about my H acting like it was not getting gas when infact it was. A couple said probably condensor or coil and not getting the proper spark. Well you were right. New points and condensor and it is doing fine. Just a question. With H's...
  4. J

    H Rims

    H and M take the drop center rims. Some 300, 350, 400 & 450 used the double beveled rims. If you change the hubs, you need to get the right size hubs for the axle size. I would just get good used drop center rims. They are available used and pretty reasonable in my area. Should be in your area...
  5. J

    Rims

    I have good success with 13.6X38 on 11X38 standard rims. Most H and M tractors had in my experience the 11X38 rim. Seems to be the most common size rim.
  6. J

    H farmall manifold

    Do you think the manifold is the problem? Had carb problem with my H. Cleaned and put in carb kit. Ran compression check and cylinders seem to be equal. Problem is that as the tractor gets warm it does no seem to be getting the correct mixture of air and gas and loses power after warm. Also I...
  7. J

    farmall H ?

    I was happy with my replacement. It had a sand hole in it that was plugged but it allowed me to add a M carburetor and since I had the cubes of a 350 it worked great. About 40 hp at 1815 rpm.
  8. J

    8/24/08 Tractor Pull, Cedar Falls, Iowa

    Who do I contact about pull for more info?
  9. J

    Tractor pull north of Cedar Falls 8/24/08

    I understand there is to be a farm stock and antique pull 8/24/08 north of Cedar Falls, Iowa at an antique threshers day. Can anyone provide info on time, rules for farm stock such as drawbar settings and rpm allowed and whether suitcase weights are allowed? Thanks.
  10. J

    HELP!!!! bf goodrich super hi cleat checkmark tires

    I have one 13.6X38 on a H rim. Do not know where to find another. 75 dollars at Dubuque, Iowa.
  11. J

    Blacktop tractor pulls

    Are the antique classes only as low as 6000? Are they standard rpm? What is required as far as wheelie bars and drawbar setup? How can I get the rules? It sounds interesting. i am in Dubuque, Iowa. I forgot to add my e-mail.
  12. J

    Blacktop tractor pulls

    Are the antique classes only as low as 6000? Are they standard rpm? What is required as far as wheelie bars and drawbar setup? How can I get the rules? It sounds interesting. i am in Dubuque, Iowa.
  13. J

    As good as it gets?

    So how far is the hitch point for the chain behind the end of the pto shaft? We are required to be not closer than 14 inches to the pto shaft. Do you mean the hitch point is 18 inches behind the center of the axle or behind the furtherest vertical point of the back of the rear tire? Just...
  14. J

    Farmall H, M, SH, SM, 350, 400 450 front wheel bearings

    Are the front wheel bearings and races all the same? That is will they interchange for H through 450?
  15. J

    HVAC schedule Dubuque, Iowa

    Anyone have the final schedule for the HVAC pulling club out of DUBUQUE, IOWA and would you please share it with me? I understand it has been changed and I have not seen a revised schedule. Thank you. Jim
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top