(800) 853-2651
SHOP NOW

Recent content by Kenfarmall

Yesterday's Tractor Forums
  1. K

    carburetor

    I took the four plugs out and all four were black and sooty, my problem is I have no adjustment on the fuel screw or air screw I had the tractor idling for 30 minutes the grey smoke did decrease some but the tractor still lopes and still no adjustment on the fuel and air screws. Is it possible...
  2. K

    carburetor

    I put a question on here three days ago about my Farmall H loping and light grey smoke, I put a jar on the end of the overflow pipe, and I do not have compression going in the coolant, my question is how do I check to see if I have coolant getting on top of one of the cylinders. appreciate any...
  3. K

    carburetor

    My farmall h sat all winter in the barn when I went to start it in the spring the carburetor was flooding. Took it off and cleaned it and ordered parts for it. In the mean time I found there was water in the oil so I took the head off and found a bad spot in the gasket between cylinder two and...
  4. K

    carburetor

    Thanks Guys for all the help
  5. K

    carburetor

    Hi Guys. What can I use for packing on the fuel adjusting needle on a Farmall H tractor Thanks for any help you can give me.
  6. K

    carburetor

    Hi Guys. Farmall H tractor, I had to clean and replace the jets in my carburetor, took it off a second time because I had the float set too high, now the tractor runs but I have little throttle response, it idles to about half the normal throttle revs any suggestions please.
  7. K

    carburetor

    Hi Guy. I tried to rebuild the carburetor on my Farmall H, when I started the tractor it was too rich (black smoke ) and the engine was lumping, so I checked the carburetor again, now I have light grey smoke and it still lumps but not as bad, but the carburetor was covered with condensation, any...
  8. K

    Head.

    Thank all you guys for the help
  9. K

    Head.

    Can somebody tell me what the torque setting is for a Farmall H head and in what order do I torque the head nuts Thank you
  10. K

    studs

    I want to put new studs in the block of a farmall H. do you guys put the studs in and let the thread seal set or do you put the head on and torque the nuts down before the thread seal is set up, will Permatex thread seal be ok How long do I run the engine before I retorque the head. Thank you.
  11. K

    studs

    Hi Guys. What do you use to seal the threads that screw into the block for the head on a farmall H. thank you.
  12. K

    weight

    Hi Guys. What is the weight of a Farmall H tractor ( no wheel weights )just a plain tractor with oil and water. Thank you for any help. Ken.
  13. K

    carburator

    Hi Guys. I checked the oil pan and I do have water in the oil, This was a reconditioned engine from yesterdays tractors 2007 this engine has only ran up and down the road a few times per year, 60 maybe 70 hours, the head gasket looks ok around the edges, could it be a bad gasket or is it a...
  14. K

    carburator

    I was thinking 1 and 27/32 was the measurement for setting the float ?
  15. K

    carburator

    I will check the oil stick for gas, I did put in a new main jet and needle valve I also put the float in hot water and it floated ok, I cleaned the carburator with carburator cleaner. thank you guys
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top