(800) 853-2651
SHOP NOW

Recent content by Lee_K

Yesterday's Tractor Forums
  1. L

    S series belt pulley shaft bearing replacement question

    I replaced those bearings on my SC without splitting the tractor. I think once the carrier/caps are removed you can move the shaft enough to get a puller/separator on the bearings. However, I did have the top off the transmission. The hardest part may be getting the belt pulley off. They are...
  2. L

    Case 310 track loader information

    I've been keeping an eye out for a 310 track loader and one came up for sale this week a couple hours away. It seems these are pretty capable machines given their size and price point. My question is what are the weak points or things to look out for on these machines? Also what would be a...
  3. L

    Case model 10 semi mount sickle mower

    I have a semi mount sickle mower. I bought it not attached to a tractor. I was wondering if any body had the brackets shown in these pictures. I would like to get the dimensions of these brackets so I can make a set for myself. They look simple enough to make out of some plate steel. I can make...
  4. L

    Case DC ring and pinion help

    A little update here. I have done a lot of research since my initial post and talked to several people. As of right now I think I will keep it where it's at but I will explain why. I do not and cannot know how this gear sets was setup before since it was shipped to me in the mail. More than...
  5. L

    Case DC ring and pinion help

    The backlash is set to 5 thousandths which is what is indicated on the pinion. I will never know what the backlash was before since this is a used set of gears from a different tractor.
  6. L

    Case DC ring and pinion help

    I'm in the process of restoring a late DC with live power including rebuilding the entire transmission due to pitted bearings and missing gear teeth. I've installed the new used ring and pinion with new bearings. I set the ring and pinion per the numbers on the pinion using the procedure in the...
  7. L

    Massey factory wheel coating

    Short question: what was the factory coating on the inside of a Massey 165 rear wheel and what would be good to recoat or paint it with. Long version: I am working on fixing a leak in the rear tire on my 165. I've got every thing apart and I want to paint or other wise coat the inside of the...
  8. L

    Case plow

    Thanks, That is what I needed to know. I'm hoping to add a remote to my VAC but I can use a mechanical link if needed. Lee
  9. L

    Case plow

    I found this plow for sale locally. What model is it? The ad just says moldboard plow and doesn't list a make or model, but it looks like a case plow to me. Will it work with my VAC and eagle hitch. I was thinking there was a lighter version for the VAC. Thanks, Lee
  10. L

    Case powered hay making

    Thanks for the kind words. Yes the rake looks to be a Kelly Ryan. I had never heard of them before. My equipment is a little light in the paint department, but a little grease and maintenance goes a long way. Thanks, Lee
  11. L

    Case powered hay making

    I will start by saying Thank You to all those that share their knowledge and working photos here regularly. I watch this site and specifically the Case forum almost daily. I have not posted here recently, but I have always gotten a good response to my stupid questions in the past. Here are a...
  12. L

    Hesston 1071 value

    Someone has a Hesston 1071 for sale locally, but they are asking 3500. That seems very high to me, but it is supposed to be in like new condition. I have not seen it yet. My question is if this is a bit steep, what would this be worth. I am in southern IN if that makes a difference. Thanks, Lee
  13. L

    Massey Fergusson 165 Diesel Starter Issue

    It works! I must admit I was skeptical. Through my searching I found a diagram on this site that shows only the nose of the starter, and it shows no washer (that I can tell). However when I disassembled the starter the first time I noticed there were two washers on the brush end of the...
  14. L

    Massey Fergusson 165 Diesel Starter Issue

    I believe the new solenoid is good. When bench testing I would use a small wire to excite the the start terminal on the solenoid. There is in fact continuity between the start terminal and the starter lug, but none between the batt lug and the start terminal. The continuity between the start...
  15. L

    Massey Fergusson 165 Diesel Starter Issue

    I will start from the beginning on this one. This summer the starter/solenoid started just clicking when you turned the key, but after a few attempts it would turn over and start. A couple weeks ago it got to the point that the engine would not turn over, the solenoid would only click. I used...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top