(800) 853-2651
SHOP NOW

Recent content by mkr100

Yesterday's Tractor Forums
  1. M

    John Deere 430 T

    I have just overhauled the engine with new main bearings ,rod bearings, new pistons 45 over. Everything has gone great thus far. My problem is my oil pressure is low. Cold around 21 psi on a numeric gauge. I didn't do anything to oil pump during rebuild other than disassemble and clean. My...
  2. M

    Two Cylinder brake latch help

    Tim S email me and I'll send photos of brake latches. Maybe you could post them for me. [email protected]
  3. M

    Two Cylinder brake latch help

    I tried sending pictures. Came back as bad email address .
  4. M

    Two Cylinder brake latch help

    My 730 has really neat modification done to the brake latches. You can operate them with your foot. It has a counter weight bout the size of silver dollar(maybe a little larger) in the back of modified latch. You can step on front side to latch them or just step on brake pedal to release them...
  5. M

    John Deere 430 T

    Im replacing the rear tires 11.2-34 on the 430. Trouble is not many tire companies are making that size. I only found one so far and don't really like the tread. My question is did any 430 come with pressed wheel 13.9-28s or was that only for the spin out rim? I want the tractor to end being...
  6. M

    John Deere 430 T

    Hello all, Im rebuilding a 430 that has set up for some time. Had water in tranny so ill replace all bearings. I have ordered a few bearings from deere and found them to be made in china. Many of the old bearings are HYATT BEARINGS they seem much heavier than the newer ones ordered. My...
  7. M

    John deere 8430

    Im not smart enough to get photos on this site. My email on my iphone is [email protected] send me a mail and i will reply with photos. Im going back to the poultry growers farm tomorrow to get serial #.
  8. M

    John deere 8430

    I can send photos to anyone's email address that would be interested. Tractor is in Mississippi. The hours are as described. It may sound fishy but it's true
  9. M

    John deere 8430

    I have a friend that just bought a place that came with a 2009 JD 8430 with only 400hrs. It"s too big for him and wanting to know what a fair price for both parties. What I know about the tractor is : IVT tranny, 480-R50 rears,front weights , wheel weights,buddy seat. Tractor has the cylinders...
  10. M

    John Deere 8400

    We are looking at a JD 8400 with 8400 hours. We will be using it to pull a 14 yard dirt pan. We have owned 4960,8760,9400,9420 using them for same purpose . None of the tractors we owned had over 5000 hours nor did we have any major engine problems. We sold 9420 two moths ago as we are scaling...
  11. M

    John Deere 8400

    We are looking at a JD 8400 with 8400 hours. We will be using it to pull a 14 yard dirt pan. We have owned 4960,8760,9400,9420 using them for same purpose . None of the tractors we owned had over 5000 hours nor did we have any major engine problems. We sold 9420 two moths ago as we are...
  12. M

    730D no start after overhaul

    Be certain that you put the governor control linkage back together correct. A friend of mine did not get the linkage in the fork on governor and had throttle jammed wide open. When his did fire it ran away. Luckily he just broke valves and thats it. Always be prepared to choke the air supply to...
  13. M

    John Deere 330 Standard

    I didn't see any cracks are welds. Im not sure about casting numbers to know if it has been pieced together at some point. I do remember final drive casting started with the letter M. I have a slant steer 420s to compare to and much of the tractor looked the same. I have also found a slant...
  14. M

    John Deere 330 Standard

    Hey guys I've found a nice 330 a older couple has. They may want to part with it.What would be a price that is fair? The tractor has cultivators and three point. The draw bar assembly is missing. Sheet metal is decent no visible weld or cracks other than a brace welded to draft arms. I was...
  15. M

    John Deere 430T dual touch-a-matic problems

    Why would it lift in the down position?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top