(800) 853-2651
SHOP NOW

Recent content by Oelke

Yesterday's Tractor Forums
  1. O

    Farmall Power Unit?

    Taylor; It has a very small Continental engine . I have one just like it, it is out of a very old I.H.C. baler.----------Harold.
  2. O

    44 Massey Engine question

    Hi, I had a 44 like that once a few years ago. the owner had overhauled it himself. the engine been resleeved with 4 inch sleevs and pistons and then run for several years. When he went to rering it he purchased original rings [3 7/8] and that is how I come to get it, engine was in great shape...
  3. O

    VA Firing Order

    Hello, Could someone please help me out? I would like to know what the firing order for a VA Case is. It is the Case engine not the Continental. Also is the little hole in the clutch housing behind the air cleaner the place tofind the timeing marks [TDC] Thank You,-------Harold
  4. O

    Massey Harris 22 Standard

    Clint; I paid a 1000.00 for one in similar shape, I put some gas and a battery in it and drove it on the trailer. Its my favorite restore out of twelve. --------Harold
  5. O

    John Deere Tool?

    It pushes the old rivits out and rivits the new sickel sections back in. Its a very good tool because you can replace a sickel section out in the field with it without having to remove the sickel from your combine or mower etc.=======Harold
  6. O

    3 HP John Deere Engine

    Thanks Bob,The nut is turned cw as far as it can go, I will start backing it off a little at a time. I hope I dont have to mess with the governor because I am out to lunch there. Thanks again --------HAROLD
  7. O

    3 HP John Deere Engine

    Hi, Got my engine starting and running but cant controle the speed. Turned the controle button both ways but it wants to jump out of the shop takeing the table I have it bolted to with it. The manual says turn the speed nut but they dont tell you which way. Could someone give me a little advise...
  8. O

    John T I need your help

    Teddy, Thanks a lot Teddy ,thats all I needed,also thanks John T for your information-. ------Harold
  9. O

    John T I need your help

    Hello , Last week I brought home a little John Deere 3HP engine [Type E]. It seems in good shape, has lots of compression but I cant get any spark. It has a mag and igniter system and I dont understand how that works since the mag has no impulse. However I found that the magnet is broken in two...
  10. O

    630 head

    The head will come off much easyer if you take three or four more nuts off.
  11. O

    630 head

    The head will come off much easyer if you take three or four more nuts off.
  12. O

    Massey Harris #60 Combine

    Hi, I think you only have to change the sproket on the cylinder to get your different speeds and there are severl different sprockets. I have a 22 and a 25 tooth sproket, used them both for wheat depending on how dry the straw was. used the 25 tooth mostly for barley and oats and in very dry...
  13. O

    Piston Rings

    Last week a friend gave a small box that contained three piston rings thinking that I may be able to use them in some tractor restoration, however they are much to small. They would fit a three and a half inch bore and are one quarter inch wide and there is no oil ring. I am thinking they are...
  14. O

    Whats it from

    Hi, Thank you very much gentlemen, you have answerd my question very well. It does not have a clutch, it has a grill, hood and gas tank similar to a small tractor. I imagin it is not very colectable . Thanks again.-------Harold
  15. O

    Whats it from

    Hello, My neibour gave me a small continental engine and I cant figure out what it used to drive. It is a very small four cylinder engine.It is smaller than the 123 ..cu.in engine. It is off of something IHC because it has a IHC mag. and IHC style IHC fan belt tightner, also the bell housing...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top