(800) 853-2651
SHOP NOW

Recent content by Philip moline

Yesterday's Tractor Forums
  1. P

    M5 ?

    670 was allot like the m5 just improved better steering and I think a stronger rearend
  2. P

    need a bearing cage

    Where is what you are calling a bearing cage located And is there a part # on it? I have been through one of these rear ends this year and may be able to help you with where to get one. I usually get my bearings from the local bearing supply store. but Im almost sure Welters would have anything...
  3. P

    HD 800 camshaft

    I'm wanting to get a cam grinded for my 800 looking for more power as always haha but need to know the best place to send it ? Thanks for any help
  4. P

    gaskets ? need help

    Buy one tube of silicone apply and install done...
  5. P

    123 Ih engine bigger sleeves?

    169.215 cubic inch
  6. P

    206D experts

    You say you have fuel to the injectors but do you mean that there is fuel at the line or do you know if the actual inj is spraying fuel? I would pull a injector hook the line back up and crank the engine and watch to see if it sprays if it doesn't you probably have pump problems.. But almost all...
  7. P

    UB timing marks

    Pump should time at 27 degrees before top dead center there is a cover on the right side of the flywheel housing (4 bolt cover ) bar engine over until you see INJ then take the inspection plug from the top of the pump adapter housing and the pointer on pump will line up with the line on the...
  8. P

    G706 rear axle

    Once you get your hub on it will hold it to your bearing and it will all turn as one. Good luck
  9. P

    Buliding a Puller

    I think it's 800 jugs or heads that put you into 5. The g jugs look the same as 800 jugs except for the water manifold holes.... But I don't know if you can run the g jugs on a u in lower divisions ??? Guess you could just tell those Deere guys that you got some of those power blocks haha !
  10. P

    UTS 1955 compression

    Well it depends on what heads you have, but I'll guess that it should be around 120 or so
  11. P

    Diesel bear ?

    How if you don't mind me asking did you get 779 ci in a u (bore and stroke).? Thanks
  12. P

    G-V1 flywheel

    You need a gvi diesel flywheel it will bolt Right on unless your 800 is a later circle Seal motor. Good luck
  13. P

    5 Star connecting rod

    Diesel or gas ? I would do some checking to Make sure before I went on someones guess. Did you get your stroker motor built ?
  14. P

    Aluminum moline weights

    Thanks for the info
  15. P

    Aluminum moline weights

    Any one know the guys name or have the phone Number for the guy that was making moline weights ? Thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top