-
T
motor oil ruining cams
So, did I get this right? We have the flat-tappet cams in our old ford tractors, but it's probably not an issue because of the low-pressure valve springs. BTW I have a '64 4000(4 cyl.) -
T
motor oil ruining cams
I don"t know if this subject has ever been on here before, so here goes. I heard from a guy at work today that the newer motor oils have reduced ZDDP(a zinc/phosphorous compound)so much that it is causing damage to camshafts on many older(pre '89) engines. Has anyone heard of this, and if so... -
T
wheel wts.
I"m going to be getting a subsoiler soon, so I"m guessing I will probably need some wheel wts. Are pie wts. easy to find? What would be an average price for a set? Do they fit on any type of wheels? Are there other types of wts.? Sorry for all the questions. Your help is appreciated. mark -
T
subsoiler
I"m thinking of getting a subsoiler to cut roots at foodplot edges and to break up hardpan(if it exists). I have no experience with one and was just wondering if they really make a big difference in productiveness of a field. Thanks for any advice. I won"t be back until Monday(11/19) so if I...- t-mark
- Thread
- Replies: 5
- Forum: Implement Alley
-
T
Carb Question
It sounds like your talking about the main jet on the bottom of the carb. Yes, I would say you definitely need the o-ring on that needle or it would leak. The needle with the spring is the idle adjustment and mine does not have a gasket/o-ring on that one either. You might be able to find one... -
T
12 volt conv.
I read over on the Smith forum that if you convert from six to twelve volt you should use a true 12 volt coil so you get hotter spark. This is in contrast to a 6volt coil and dropping resistor. The latter is what I have. If I change to a 12v coil do I leave the resistor on, or take it off? Does... -
T
The harder the better...
That sounds like a nice size tractor to have. Is it category I or II? Is she a heavy drinker? mark -
T
The harder the better...
Sounds like a bad hombre! What's the horsepower on those again. -
T
ford 800
Bloomune, I was having the same trouble as you. My screens(fuel shutoff and sed. bowl) were in good shape, the rust was simply going through them. I had my tank lined with the epoxy and cleaned the carb. I've only ran it under load twice since then but both times it ran just fine, no faltering... -
T
valve cover leaking
Glen, where did you find the spec. I looked in my owners manual and the IT manual and coudn't find it in either. Maybe I just didn't look in the right place. mark -
T
valve cover leaking
Thanks for all the good advice, guys. When I go see Ol' Blue next weekend I'll have to determine which nuggets of info I'll have to use. mark -
T
valve cover leaking
1 1/4 to 2 in. lbs? That doesn't sound like much torque at all. I'm sure I have a lot more than that on it. Maybe that's my problem. -
T
valve cover leaking
I recently had the gas tank off on my "63 4000(172ci) so I decided to change the gasket on the valve cover while it was easy to get to. Well, sure enough, now it leaks. Anyway, I just wonder if anyone has any tips. The new one is the rubber(neoprene?) type. All surfaces seemed to be clean when I...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy