(800) 853-2651
SHOP NOW

Recent content by WOK

Yesterday's Tractor Forums
  1. W

    T340/TD340 Questions

    I've a T340 with a Drott loader and street tracks to sell. Good condition. Central Iowa -- WOK
  2. W

    F20 Cultivator Model

    robgIN-- Thanks for the model information. Would you photo copy the parts book? I'll remberse you and e-mail me and I'll get you my address. I believe I've all mounting part, outbut there is one I can't figure out. Thanks
  3. W

    F20 Cultivator Model

    Can someone tell me model of cultivator I have for a F20. It is a 2-row with a PTO driven power lift. The front pull bar is angle iron (not square or round as some were). The ganges appear like the ones on a F12 picture in the Spring 2015 HARVESTER HIGHIGHTS, page 28. I'v no F20 & it's been...
  4. W

    Generator Cutout Problem?

    Thanks for your suggestions and comentents. The generator was rebilt and checked out. Most likely the cutout ground may be the problem. I've adjusted the cutout down to a weak spring too and it stays closed at higher tension too after I manually close it.
  5. W

    Generator Cutout Problem?

    On a 42 H with orginal generator and cutout: With the switch high charge setting the generator (been checked out) puts out 12 amps when cutout is manually closed (stays closed) at higher engine speed then back to idle speed it discharges 4 amp for 10-15 seconds the to 0. At normal (low) switch...
  6. W

    IH 300 Value

    I"ve looked at 1955 300 w/TA in an estate. It"s been inside for years with a stuck valve for sure. Aparently it was started to be worked on as hood is off and power steering partially disconected. I couldn"t see the tires because it was nearly coveer up with lumber. What should I offer...
  7. W

    44 Trasmission Bearing Cage Leak

    The lower trans. bearing cage leaks around the shims. Will spray gasket sealer be thin enough or possibly liquid teflon where the cage enters the trans. case work? I"ve pulled the cage out 1/2" (with outter bearing to nut near the shaft end}. Will the shaft remaine centered enough if I remove...
  8. W

    chaining down your Farmall?? Your thoughts please.

    I've bolted a 3/8"x3"x8" plate under front wheel pedistal (2 5/8" bolts) then attach a hook clevis and chain going 2 ways. On the drewbar I use clevis' on the corners. - WOK
  9. W

    1949 - 44RC Decal Placement

    The decal kit I obtained has 2 decals I need help on, if they were used originally. The "Recomended Air Pressures" was where? Was it possably on the outside of the sliding tool box as there may have been one there? The '52 parts book shows one in the kit. The other decal is a 2 line (5/8"x3...
  10. W

    44-6 GR

    Check the serial number stamped on top of the rear housing. the frame may have replaced.-WOK
  11. W

    44-4 Head torque?

    Can someone give me the head bolt torque specifications? I"d like the manifold torque spec"s too. I couldn"t find it in the owners manual. Thank in advance. WOK
  12. W

    '49 44 Painting

    Thank for your responses. On my others I've never had them paint the new wiring either, but they do at factory. WOK
  13. W

    '49 44 Painting

    Thank for your responses. On my others I've never had them paint the new wiring either, but they do at factory. WOK
  14. W

    '49 44 Painting

    I'm preparing to sent my restored 44 to a paint shop.It has never been repainted and we were able to compound buff an unexposed area to match the original paint. My question is when restoring to original do most of you paint the wiring? Originally the wiring, choke cable and temp. guage cable...
  15. W

    44 Light Parts

    Restoring a '49 MH 44. Is there a source for head light parts? I'm in need of one bright silver (chrome, nickel or stainless???)lamp molding ring. I could use a better reflector assmble too. I may have make the gaskets if none available. Thanks & Merry Christmas. WOK
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top