(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. T

    Allis Speed Patrol grader

    This is for sale near me and I'm very tempted to try buying it, but it has me a little confused. I thought these speed patrols were just based on wc models? This looks like a wd45 to me because of the snap coupler. Was it maybe one that someone retrofitted the grader parts to a later...
  2. T

    Hydraulic loader problem

    I recently picked up a Massey 204 for a great price, and after a tune up and carb rebuild it runs a lot better than it did when I got it. I have an issue with the loader however. When I try to curl the bucket, up or down, when it reaches the last few inches of the cylinder it bogs down the...
  3. T

    Dc motor off ac power

    I have an old engine driven welder I just got running decent and now I'm wondering about the feasibility of putting this wire feeder on it for occasional sheet metal work. My welder has a 110v outlet at 50 hz. This wire feeder I believe has a DC motor, is there a simple way to run it off the welder?
  4. T

    1 arm loader value

    There is a 1 arm loader with hydraulic tilt for sale near me, but the price seems a bit high. What's the going rate for these? It might have brackets for a 601, and it might have a 2 spool valve. I have a trip bucket one and would like to replace it with a hydraulic dump.
  5. T

    Farmall 340 rear end

    My neighbor has a 340 that he is looking to sell, I went over and took some pictures to post it for him, but in the process, I found an issue. When the pto is disengaged it starts making a loud squealing noise, but when it is engaged the noise goes away. Does anyone have an idea on what the...
  6. T

    Need help with electric motor

    I bought an old drill press last week and it has a 3/4 horse electric motor on it. The motor hums but it will not run. I tried spinning it while it was on to see if it would start and it still would not. I pulled the motor apart but I don't know enough about electric motors to even start...
  7. T

    Rottler Boring Bar

    I have a chance to pick up an old Rottler CA boring bar cheap, but it is missing some parts. Does anyone have parts or tooling for one they'd sell? Or even a whole bar?
  8. T

    What have I got myself into this time? (Free Trailer)

    I just got this trailer from some relatives who didn't want it anymore and actually parked it in the fence row about 10 years ago now. After dragging it out and filling up the tires with air I proceeded to pull it home and only had to stop once to put more air in one of the tires. Now I get the...
  9. T

    Case DC wide front

    I just obtained all the pieces I was missing to install an adjustable wide front onto my DC-3. Before I install it I need to do some work to it and I would like to replace the tie rod ends. Does anyone have a source for them? I already had a good axle but a broken gooseneck but today I...
  10. T

    901 diesel to gas

    I just got a running gas engine to put in my 981 D with bad rod bearing, while I still have the gas engine out, should I replace the rear main seal? It doesn't appear to be leaking currently.
  11. T

    Lincwelder 225

    I just took this engine driven welder on trade for a Farmall M, does anyone have a wiring diagram or service manual for it? I would also be interested in a service manual for the engine if anyone knows where I could get a pdf version of it. I need to replace the fuel line and I am going to...
  12. T

    Trades?

    When selling a tractor or implement on FB or Craigslist, do you state that you are open to trades or that it is cash/check only?
  13. T

    Case DC update

    I know it has been several months since I last posted about my DC, today I got it running and was finally able to drive it around. The last time I had it running was about 8 months ago and I was unable to drive it do to transmission problems, since fixing those, I have not been able to get it...
  14. T

    Crossmotors for sale

    I saw these on Craigslist, I don't know anything about them but I hope someone can save them. Untitled URL Link
  15. T

    Titling a Canadian car in US

    I have a relative who bought a 1960's Ford Custom in Canada and brought it to the US. He did this 15-20 years ago. He never registered the car in the US, he parked it in a shed. He has since moved and lost any of the paperwork he filled out to get the car to the U.S. Does anyone know what he...
  16. T

    Funny

  17. T

    Steamer or crossmotor?

    The post below got me wondering, what would you rather have, a Case steam engine or a crossmotor? I would rather have a small crossmotor.
  18. T

    Re: My 871 loader needs more traction. I need a c

    Why does she want it on its end? I don't think a 3 point spear would be any worse than one for a loader for moving a bale like that.
  19. T

    Case DC for sale

    I talked to the seller and the engine is free. It is a 52 serial number on the block. It appears to have a 5505 head. FB marketplace ad
  20. T

    Case VA thoughts

    I was offered this VA for free, I went to look at it today and took some pictures. The person says he has 2 more, one of which was apparently reversed and used as a sweep for putting up loose hay. I haven't seen the other 2 but he says the reversed one was free a couple years ago and that he...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top