(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. B

    L or LA rocker arm questions

    I'm trying to determine where the oil holes in rocker arm shaft are positioned in relation to rocker arms. There is an oil hole on top of rocker arm and one bored towards push rods. Any help or pictures would help. Thank you, Brian
  2. B

    L/LA rocker arm shaft question

    Could anyone tell me which way the lubricating holes face on the rocker arm shafts on model L. Thank you. Brian
  3. B

    1930 L head

    Started on the head today. As picture shows one stuck valve and one raised guide. The valve should free easily with some fluid and time and small hammer. Not sure about valve guide. I"ve broken one before tapping with medium hammer. Any advice? Thank you, Brian.
  4. B

    moss control

    does anyone have suggestion for killing moss on roofs with household chemicals or other inexpensive chemicals. Thank you. Brian
  5. B

    worked on the 30 L

    Pulled the head. Started removing rust. Soaking pistons with penetrating fluid. I broke one head stud. Any advice on that? Will start working on pistons with a block of wood and small hammer with patience. Brian
  6. B

    magneto questions

    I just pulled this off my 30 L. First time dealing with a magneto. I assume lever on front is on/off. Mine moves from 3 oclock to 5 oclock, but need to use some force. Not sure what metal strap from center screw to lower left screw is for. And do I need to get into it to service. And how...
  7. B

    pulled the head off the L

    pulled the head with the help of a front end loader, nuts and head were easy. One cylinder still holding water after months under cover. Is this automatic sleeves and pistons or has anyone salvaged something like this. Any thoughts welcome. Does Case/IH still sell these parts or other...
  8. B

    removed valve cover on the L

    finally got the manafold off then the valve cover. Looked better than expected. Oil tube was worn through from push rod contact. Next remove head. Any thoughts? Brian
  9. B

    put her to the test today

    First time out after restore, hauled the 49 8n front mount out to mow. This was also my first time using a sickle mower. One hour in she died, no spark. Took the dizzy home found no continuity with points closed. New points not available in time, so sanded and cleaned. Put back together...
  10. B

    30 L prefilter question

    started with the prefilter, had to cut it off. Was this an original part or aftermarket? Any info would be more than I know now. Thank you. Brian
  11. B

    got the L home, where to start?

    got her home today and in a new resting spot. Where to start? I think this one will cost me a little and take some time. I just can't turn them down. Brian
  12. B

    dearborn 14-15 sickle mower

    I was given this mower last fall, fixed a few things, tuned it up, and it works well. I found the owner's manual online, but could someone tell me the years these were made, and are they still around being used. Thank you. Brian
  13. B

    1930 case L

    Took a closer look and some pictures. Manifold cracked, radiator? looks rough, rear wheels rusted out gone, sheet metal looks good, price is right-free. Any thought from those who have done this before. What am I in for dollar wise? Are parts available?
  14. B

    Case L questions

    Hello all, this is my first time on the Case site, I looked at a L today that I can have for free. I'm not sure of the year yet. It's been outside, all rusted, exhaust covered, sheet metal looks good, rubber tires are shot, everything else looks complete. From what I can tell parts seem hard...
  15. B

    looked an an m today

    I looked at an m today, serial #fbk 105739 x6 Chicago Ill. 1595. I understand it was made in 46 but I don"t uderstand the fbk x6 or 1595. It also had a mw clutch tag and housing on left side I"m not familiar with. Single front tire. 3pt hitch. Hydraulic line from both sides of tractor. I...
  16. B

    27v mower to Super C

    I hooked up my new find to my super c. A little grease and all works. Now I need to build a cable pulley system to raise and lower unit. I am open to sugestions how and where to run cable. Thanks for help. Brian
  17. B

    27v hook up help

    I"m trying to hook up a 27v sickle mower to a Super C. Can the cutter bar be raised/lowered with touch control rocker. If so does anyone have photo, picture, or drawing of set up. Thanks for help. Brian
  18. B

    help identify

    It has the IH logo, but has been modified some. Can anyone give me a model name or number. Did it have the fast hitch prongs originaly? Are the hydraulics after market versus manual? Any info would be great. Thank you. Brian
  19. B

    axle hub removal success

    Day 5, 12 dollar rental fee later and a few hefty hits with a 4lb hammer and bang, off they came. Thank you all for the advice (get the right tool for the job). I ordered parts off this site today. I live in Oregon so they usually arive in three days. Then my wife can have her parking spot...
  20. B

    axle hub removal update

    Day 3 lost the wd40 used pb blaster, lost the weak sister puller used her bigger brother. Two rounds of heat and 4lb hammer from every angle. Still no luck. Next to check rental store for hub puller. After that I am prepared to remove whole unit to have pressed out. Thank you for advice so...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top