(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. 4

    needing tractor hauled from ks to co

    bought tractor in ks and needing it hauled to co if anyone has any connections...
  2. 4

    looking at case 2294 anything to beware of?

    I was looking at a case 2294 7175 hrs 3 spd powershift. Is there anything I need to beware of? I am familiar with case and am aware of the change from the cable shift to electric shift in the 90 series to the 94 series transition, As well as an optional 6 spd powershift. This tractor is an...
  3. 4

    tractors on big iron this week in NE

    I was looking at a 4440 and a 4450 in Wilber NE was wondering if anyone here was from that area and were familiar with the tractors. It appears to be a retirement auction.
  4. 4

    roosa master not running after replacement

    on a 544a the injector pump was replaced and very little fueu coming from injector lines. it is all rotating, as well bled as i can get it, transfer pump at back cover is pressuring up. good fuel delivery from tank fuel is coming from return on top cover in steady stream with line cracked while...
  5. 4

    funny horse for sale poster

    A message was posted within the last few months containing a horse for sale poster that was hilarious. I saved iton my phone but recently switched phones. anyone know how to find this generic horse for sale poster?
  6. 4

    agco big baler shims

    On a 3x4 2270 massey/hesston the load arm from the gearbox to the plunger has 2 arms, a left and a right. How do you shim the 2 sides to get correct? Is there a measurement or a do you bolt both up and tighten up until one is clear then add shims to get symmetrical?
  7. 4

    salvage yards with big balers

    I am looking for a salvage yard that might have some agco big balers any ideas where may have something?
  8. 4

    agco parts breakdown

    I was working on a baler (3x4) and there is a shaft that is bad. I was wondering if I can rebuild that shaft or if I buy the entire crank arm assembled with shaft. I was hoping to find an online parts break down to seeif it lists these parts seperate or as and entire assembly. Thanks.
  9. 4

    4440 value

    I am wondering what a 4440 like this might be worth about today, unknown actual hours, a lot of work done such as front end re bushed new fluids and new belts, new tires, 3 remotes, water pump just rebearinged and resealed good ac good heat, quad range, all lights and gauges work, axle mount...
  10. 4

    4440 door seals

    I'm looking at replacing door seals on my 4440. I went to order and the supplier said all I need is a roll and glue it on. I wonder if there is a recommended supplier or atleast part numbers for the door seal and the other seal that goes onto the cab with the wire clips. Thanks.
  11. 4

    466 inline pump timing

    The 466 engine with inline pumps have slotted mounting holes for pump timing, I loaned my book out and never saw it again and was wondering if someone could post/say timing direction for advance/retard. I believe I know but I want to be sure. thanks.
  12. 4

    4440 water pump loose

    Iwas going to put this tractor for sale and was wondering from the expert experience the water pump is a little bit loose, but no leaks at all. should I figure it is normal until it leaks or just rebuild the pump and know its right for the next guy? I am pretty certain a new pump would be tight...
  13. 4

    4440/4250/4450 revs on start up

    These tractors are designed to do this, how and why? just curious.It appears to be an oil pressure related aneroid that allows the engine to rev until a certain rpm/ oil pressure/ boost is achieved then it idles to the throttle setting. Is this an oil pressure system? Mine I can kill the fuel...
  14. 4

    71 units

    is there any demand for the old 71 units anymore? I found some in nice shape was wondeering if anyone had a local market for them.
  15. 4

    john deere draft control vs. case/massey/ih??

    I have wondered for a while now why the john deeres do not lift the 3 point hitch under load like a case, massey, ih, ?? I have ran plenty of john deere 20 series, 30 series,40series, 60 series, and case 70 series 90 series, and masseys and IH. In the same soil, pulling the same 4 bottom plow,or...
  16. 4

    4440 draft and load control adjust

    Anyone have a list/photo copy/ picture of the adjustment for a4440 load controlshaft nut iniside the transmission housing? Mine needs done and I seem to have lost/misplaced my factory manuals. Iremember that you set the draft to minium and pull back on lever to like 5 to see start to lift then...
  17. 4

    john deere roll over plow parts

    anyone know of any slavage yards that might have some rollover plows in them?
  18. 4

    mystery suitcase weights

    I recently acquired a handful of suitcase weights, they have a BZW casting, as well as a bw 202 feel to be 80-100 lbs each, looks to fit ford or massey. Anyone know what these are?
  19. 4

    1070 hydraulic valves

    I need to go through the lift arm and scv service valveson a 1070 case. Can I get tothese from the operater station under the seat? Or do I need to remove fuel tank and/or cab? The lift arms bleed off and it has some scv issues as well.
  20. 4

    1105 draft controls

    Anyone have apdf of the1105/1135 op manual that explains some of the menagerie of the draft sensing adjustments, I have the lever in the cab figured I think, and the turn knob I believe, My next considerations are the location of the top link mounting bar on the tractor, has 2 sets of holes, the...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top