(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. B

    C 301

    Is it possible to sleeve a c 301 engine block with two cracked cylinder bores? thanks
  2. B

    Goodyear Power Torque tires

    Seen an add for a set of new old stock goodyear 6 ply 16.9 x 38 power torque tires. dont know much about them. Would they be a decent tire for pulling?
  3. B

    Farm all M governor spring

    I was looking to replace my stock M governor spring. I was told that I can get a little better than stock spring from TSC in the hardware section. Does anyone know the part# . Thanks
  4. B

    Farmall M Governor Spring

    I was looking to replace my stock M governor spring. I was told that I can get a little better than stock spring from TSC in the hardware section. Does anyone know the part# . Thanks
  5. B

    Farmall 460

    I've been giving some thought to putting a 291 engine out of a 756 in my 460. I know I will have to change the front cover to fit it in. Any other problems I might run into ?, like stearing shaft ? oil filter housing? Im going to run it in 3-3 1/2 mph class, what weight class do you think it...
  6. B

    Farmall 560 tel a depth valve

    Recently the steel hydraulic lines running from the tel a depth valve to under the seat have started to leak. Due to the fact that I really don't use the fast hitch and the extremely high cost to replace the steel lines I have decided to delete them. My question is if I un bolt the lines from...
  7. B

    Farmall 560 Tel-a-depth valve

    Recently the steel hydraulic lines running from the tel a depth valve to under the seat have started to leak. Due to the fact that I really don't use the fast hitch and the extremely high cost to replace the steel lines I have decided to delete them. My question is if I un bolt the lines from...
  8. B

    Farmall 560 head

    I have a 1958 Farmall 560 that I pull with. It does ok but I know I need to rebuild the engine. It appears to have the stock 263 gasoline block and head. I have ruled out putting a bigger engine in it, and I know I will be limited as to what I can do to that engine. My questions is what cylinder...
  9. B

    Farmall 560 Cylinder Head

    I have a 1958 Farmall 560 that I pull with. It does ok but I know I need to rebuild the engine. It appears to have the stock 263 gasoline block and head. I have ruled out putting a bigger engine in it, and I know I will be limited as to what I can do to that engine. My questions is what...
  10. B

    Little Genius Plow

    Yesterday I purchased, what I think is a Little Genius #8 One Bottom plow. Im not a 100% sure that it is not a Little wonder plow. It has steel wheels and a steerable tail wheel. With that I think Its a #8 little genius. Ive tried looking it up but it doesn't show much on the one bottom #8. Is...
  11. B

    Tire psi

    First time pulling my farmall M this year. I was wondering what a good air pressure to run in the rear tires. 13 6 38.
  12. B

    460 vs 560

    I was thinking of building a tractor just for pulling. I would keep it kind of stock but bigger pistons and loose some unwanted weight. What would be a better choice, a farmall 460 or 560 ? (Gas)
  13. B

    Body Filler

    I want to redo the fenders for my Farmall M, they are in good shape except for some rust pocking. I am going to sand blast them first and use a quality filler but my question is, Do I prime them first and then apply the filler or apply the filler on bare metal before the prime coat? Thanks!
  14. B

    Farmall M miss under load

    Over the winter I rebuilt the engine on my 52 M. I took it out over the weekend to do some plowing. At an idle she runs very smooth. I started plowing and it ran ok. Once I hit a few tougher spots in the soil and started to work the engine harder it developed a miss. once I got into better...
  15. B

    Tire Air Pressure

    I'm going to do some plowing this weekend with my Farmall M pulling a 3x14 plow. Was wondering what psi to use in the rear tires. 13-6-38. Thanks!
  16. B

    Famall M single wire alternator

    I am doing a single wire alternator conversion to my 52 M. I have not been able to find many wiring diagrams for a one wire conversion. I have it mostly figured out with the exception of the correct placement of wires to the amp gauge. 1- What side does the wire coming from the alternator go...
  17. B

    12 conversion coil

    Doing a 12 volt conversion on a 52 M. I bought a 12v coil to put on it. Could I have left the 6v coil on it and would it have worked?
  18. B

    IH Model 60 plow set up to M

    Recently I purchased a IH model 60 3x14 trip beam plow. As best as I can tell it is a narrow frame 3 bottom reducible to 2 bottom. I will be pulling it with a Farmall M. My question is, does anyone else use this combination of plow and tractor? And if so how do you have it set up?, such as the...
  19. B

    IH # 60 plow

    Does anyone know what years they manufactured the international model 60 plow. Thanks for your help!
  20. B

    International #60 #70 Plow

    I am looking to buy a 3 bottom trailer plow. How do I tell the difference between a #60 and #70 plow? What part of the plow would be the best spot to measure to tell if its a 3x14 or 3x16? Thanks!
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top