-
Ford 2600 steering wheel shaft repair
Working on a 2600 with the typical p/s leak out from under the steering wheel. This is the third tractor I’ve done. I’m using the same repair kit from this website that I’ve used the past two times, but this time the shaft is so worn down that I can put the speedy sleeve into place by hand. Has... -
MF 230 Gas Fuel Tank and Clutch Questions
Just picked up a Massey Ferguson 230 gas. It’s missing the fuel tank and the mounting brackets that go with it. Would anyone be able to send a picture of what the mounts look like so I could make some, going to check out a few junk yards nearby but there’s not many masseys in our area so I’m not...- Josh M.
- Thread
- Replies: 2
- Forum: Massey-Harris & Massey Ferguson
-
Ford 9600 motor weight?
Anybody have a rough ballpark on the weight of a 9600 motor with all the accessories on? (Manifolds, turbo, flywheel, clutch) -
Ford 8730 powershift locking up
Started up the 8730 to bale and in any low range gear in forward the tractor will drive forward maybe 10 feet and something in the transmission locks up and stops the motor immediately, in reverse it really struggles to move so I haven’t driven in reverse much. High range forward (10th and... -
4020 Clutch
Need insight on what you guys use for clutches on a 4020. Buddy of mine put a brand new hy-capacity clutch in after we did a full rebuild on the motor. Its had 600 hours on it since rebuild and it’s wore out the pto clutch fingers once (they are not riding on the release bearing when the pto is...- Josh M.
- Thread
- Replies: 9
- Forum: John Deere
-
Ford 7600 head gasket
Our 7600 rowcrop blew the headgasket. As far as I know it has the factory 256 motor. Are there any differences on the 256 motors I need to look out for when buying a top end gasket set and head bolts for this motor? And am I better off getting parts from the dealer or a reliable parts website? -
Ford 8730 power steering orbital valve
Just resealed the power steering pump and orbital valve on our 8730. Put it all back together and the orbital valve is dripping the same way it was before I sealed it. I torqued everything to spec from an online manual I found, the bolts on the bottom cap are a little over 16.5 ft-lbs (my inch... -
Ford tractor parts breakdown
Just went on the New Holland website for the first time since their new update. I cant seem to figure out how to get to the parts breakdowns like we used to be able to, seems that we can only lookup part numbers anymore. Anyone else have success finding those? -
Ford 3000 draft control
Just rebuilt the hydraulic pump and top cover on a 1965 ford 3000. When nothing is hooked to the 3 point it lifts fine, but when I put the brush hog on itll lift a few inches and quit. If I lift the back of the brush hog a little bit by hand itll lift the rest of the way. My question is how do... -
Ford 3000 3 point
Picked up a 1965 3000 with a 3 point that lifted really slowly. So I drained the oil and got sludge and water, pulled the top cover to find a layer of sludge on the bottom and a few gear teeth. Return filter was plugged and the suction filter was torn and completely packed with sludge. Fast... -
Gehl 1060 chopper
I have a 1060 gehl that is currently plugged up pretty good. The little electrical box has a forward/reverse switch for the head, but as long as Ive owned it the reverse has always spun forward. Im not really familiar with the chopper, rarely use it, bought it to chop up some weeds in a big...- Josh M.
- Thread
- Replies: 0
- Forum: Implement Alley
-
Ford tw-25 series 1 dash lights
Im working on our series 1 tw-25 and Im trying to get the air cleaner light and trans pressure lights to work. I have 12 volts at both light bulbs, I havent load tested it but Im assuming its good power. I just cant seem to figure out the ground side, the wiring diagram I have is extremely... -
6.6 Brazilian 6 bolt crank
Would a 6 bolt crank out of a tw series motor swap right in to a Brazilian 6.6 truck engine? -
Ford Excavator
I have the opportunity to pick up a ford excavator for free, supposedly ran but cant get it to start again, only on ether. Its a 401 motor and Im pretty familiar with them so that shouldnt be much of an issue. My main question is about parts. The left track tensioner is either broken or has a... -
Oliver 1265 questions
Working on the neighbors 1265 Oliver, I was curious how much oil the motor takes, as well as the transmission and rear end. Also is there an internal hydraulic filter? Im a ford guy and I dont know anything about these fiat built Olivers.- Josh M.
- Thread
- Replies: 1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
New holland l228 valve clearance
This is probably the last website I should be asking this question on but hopefully theres someone that knows, Im in a pinch right now lol. Im putting the head back on my buddies 2017 l228 skid steer and I need to know what the valve clearance should be. I was going to go somewhere...- Josh M.
- Thread
- Replies: 0
- Forum: New Holland
-
Ford 4200 wide front
Anybody know the bushing sizes for the spindles, and spindle size too, looking to rebuild this front end. King pin is shot too if anyone knows what the specs are for these axles please let me know. Shes on her 3rd motor and Id love to get 3 more out of her. Grandpa bought her brand new in... -
Badger silage wagon color
Picked up a badger silage wagon for super cheap in pretty good mechanical shape, just curious what color green they used for these wagons? Almost looks like our artsway grinder and an old Oliver 77 we have, but we are wanting to paint it up with the correct color and arent sure what to use.- Josh M.
- Thread
- Replies: 3
- Forum: Paint and Bodywork
-
John Deere 2550
Thinking about picking up a John Deere 2550 from a local company, it has 3600 hours and has been sitting for probably 15-20 years. Its been started and ran a couple times each year, just hasnt been worked. Theres a couple electrical issues, seals leaking, and the paint is faded. If I was to...- Josh M.
- Thread
- Replies: 8
- Forum: John Deere
-
White 2-115
I have a friend with a white 2-115 with a detroit that asked me to rebuild his pto clutch pack for him. Im a ford guy and dont know too much about the Oliver tractors, so would this 2-115 be the same as an Oliver 1950,1955? And from what I remember seeing, those clutch packs come out of that...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy