(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. M

    Massey ferguson 35 draft control assembly

    Hi guys. I want to replace the draft control assembly on my MF35 as its all worn at the holes around the yoke and clevis to an oval shape. There's a slap in it up and down and in and out. I've had the assembly out a few years back when I had the lift heard off so there's no problem...
  2. M

    Fordson Super Major

    Hi going to change the rear crankshaft rope seal on a fordson major that's been leaking since I bought it. Probably has never been changed since new so in reality will it be possible to get it stopped with a new seal and what's the best way about doing it. Thanks.
  3. M

    Ferguson 2 furrow plough

    Hi I've a ferguson plough I'm starting to restore. A few bits missing unfortunately. On the furrow wheel can anyone show me where the spring goes? It's missing on this one and the exploded diagram I have is not the best Any other information appreciated Regards
  4. M

    Rope seal leak v engine sump Cork gasket

    Split the Massey ferguson 35 3 cylinder which has been leaking alot of oil and I honestly can't figure out if its the rope seal or the engine sump that's leaking. Transmission plate had alot of engine oil in it. From the pics. What's your guesses? As you can see there appears to be no oil...
  5. M

    MD 35 Rear crankshaft seal

    This message is a reply to an archived post by Cormiers Cove on September 02, 2021 at 20:45:00. The original subject was Re: MD 35 Rear crankshaft seal. I've ordered one of these today. Will have it by the end of the week and install it over the holidays. How has the seal worked so far for...
  6. M

    Massey ferguson 35 problem

    Hi, I was driving my MF35 dual clutch today when all of a sudden it just slowed down and wouldn't drive. Could put it in any gear high and low let out the clutch but nothing would happened. Had to tow it hope. PTO is engaging OK and so is the lift. What problems am I looking at or Where's...
  7. M

    Ferguson 2 furrow plough

    Hi I'm looking for a ferguson 2 furrow plough manual. Does anyone know if they are available online or anywhere? Thanks
  8. M

    Massey ferguson 35x Cross shaft O Ring

    Hi, I've a bad enough oil weep coming from the hydraulic cross shaft. I'm guessing it's the o ring that needs replacing. Big question is, is it anyway possible to replace that O ring in attached photo without taking off the hydraulic lift cover and a major dismantle. If you think it's...
  9. M

    Ferguson 20 lift going down when engine shut off

    New rings in piston and the lift stayed up when shut off for a day or 2 but now goes down within 30 mins. What would cause this?
  10. M

    Brass Brazing flux Sliver solder flux

    Hi just wondering would brass brazing flux work on sliver solder brazing? Some tin work I'm doing
  11. M

    Ferguson 20 draft gasket

    Hi, I'm renewing the draft control on a. Ferguson tef 20 that was totally seized and parts badly rusted. There was no gasket originally it seems on the triangle plate that bolts to the lift head. (arrow in pic) I'm thinking of putting one in, it would have no ill effect on the system I'm...
  12. M

    International b23 finger bar/sicklebar mower UK made

    Hi, I've recently discovered that IH changed the cutter bar on the B23 in later years of production. The fingers were in doubles and the knife head was different and the guides and clamps all had shims. I have one of each but I need a knife head for the later version. (left of pic) More...
  13. M

    TEF 20 hydraulics jammed up

    Hi A Ferguson 20 I have just bought has got the Hydraulics jammed in the full up position and won't go down. I've pulled the hydraulic cover off. Checked the hydraulic pump and it appears to be pumping oil. The cross shaft and draft assembly are totally seized and took some amount of heat and...
  14. M

    Massey ferguson 35 hydraulic top link

    I want to put a hydraulic top link on Mt massey ferguson 35 3 cylinder dsl. What do I need to do? Has anyone got this setup? I know the diverter valve system with an outflow and return spool valve system but that wouldn't suffice with a hydraulic top link Thanks
  15. M

    IH B23 finger bar mower

    Hi, currently restoring a International B23 mowing bar 3pt linkage. Does anyone have an exploded diagram of the mowing bar where the knife slides up into and a picture of a knife for one?
  16. M

    T bar pick up hitch

    I'm posting this here also as the Ferguson 20 T bar hitch is similar mechanism https://www.yesterdaystractors.com/cgi-bin/viewit.cgi?bd=mf&th=199717
  17. M

    Massey ferguson 35 t bar pick up hitch spring renewal

    Hi all hope your all keeping safe. The tension on the spring of the t bar has failed alot and I'd like to change it. Anyone any information or ever changed one themselves before I tackle into it? Any help appreciated always
  18. M

    Massey ferguson 35/135 swinging drawbar mounting plate query

    Hi all, I'm wondering as anyone got the measurements for the hitch plate that bolts on the underbody of a MF 35 /135 to attach a swinging drawbar. PIC attached of what I'm talking about. I can't source one 2nd hand and got a price for a new one which I thought was crazy so if I knew the...
  19. M

    Massey ferguson 35 foot throttle fit

    Hi all, hope everyone is keeping well and safe. I'm fitting a foot throttle to a MF35. I've all the parts and fittings bar 1 crucial part that can't be bought. Part 72 where the arrow points. Just wondering if anyone has any advice to the length and and angle of the bends to linkage...
  20. M

    Ford 4610 front crankshaft seal

    Hi, the front crankshaft seal needs replacing on my Ford 4610 2WD. The seal is in the timing cover so ill have to take that off. What lies ahead of me when I go to do this? Do I need to remove the front axel or will I be able to take the timing cover off with just the radiator off...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top