(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. M

    4020 Gas MS Carb

    Is it possible that boiling the gas in a MS carb could bend the float changing the float level adjustment? The story; my 3020-diesel started leaking at the hydraulic pump, so I put my 4020 gas on the haybine. It was pretty hot and I just wanted to make one more round and it started running...
  2. M

    New Addition

    I just acquired a MF 65 gas in an online auction, picked it up last week. It is a very clean early model with power steering and good rubber. The grill screens and the pan in the front are dent free. It also has the starter wheel weight. The battery was dead, but it started right up with the...
  3. M

    Muti-Power question.

    I acquired a MF 135 diesel with the Multi-Power switch on the dash, operating the switch does nothing and I assumed the high clutch was out and the tractor was driving on the low-speed dog clutch. I took the tractor down a small hill to test my assumption and discovered it has good engine...
  4. M

    Electrical Question

    My son purchased a house a couple of years ago, during a period when I had some health issues. Actually, when I told my son I was too tired to attend the inspection he sent me to emergency where they discovered a clot in both lungs. Now to the issue, recently he had a high electric bill, which...
  5. M

    Generator Success Story

    On this forum from time to time, we attempt to diagnose issues with generators. Sometimes without success. I acquired a 7500-watt Generic portable generator on an on-line auction. Someone and been working on the carb, not a good sign. After I removed and cleaned the carb it would start and...
  6. M

    Bird Feeder

    I had some bigger birds at the feeder.
  7. M

    MF 202 Filter Recommendations

    My 202 recently sheared the key in the front hydraulic pump while my son was using it. I ended up pulling the pump and replacing the key and it appears to be ok. Troubleshooting the issue, he removed the filter next to the pump, and he said it looked pretty bad. Looking for the correct filter...
  8. M

    Putting the Generator away

    I am putting the generator away after its use in the recent outage here in Michigan. The house power stayed on so it's the one at the farm. I have a small electric pump that I use to pump all the regular fuel out of the tank. I then refill with some REC fuel, run the generator a bit and shut...
  9. M

    Refueled with REC Fuel

    Just came off a 64-hour outage on Friday cause by a little storm last Tuesday. I got 7 different restoration times from the utility along the way. Yesterday I drained the regular gas in the generator tank and replaced with REC. I like to store it with REC fuel. Does anybody else do that?
  10. M

    New Welder

    Well, new to me. A few weeks back I bought a welder on a local online consignment auction. I was not able to go look at it, so I bought it sight on seen, not a good plan. It was part of an estate and I got it for under $200.00 so I took a chance. It's a Miller AEAD LE-200. A friend and I...
  11. M

    Fluorescent to LED.

    I have three fluorescent yard lights at the farm. It seems the bulbs have a rather short life. When I went to get a replacement at Home Depot, they didn't have any and the clerk referred me to a LED replacement. On the package it said in large print replaces large base fluorescents and sodium...
  12. M

    Addition to the Herd.

    Addition to the herd MF 275.
  13. M

    Unknown Ford tractor part

    Any body know what this is? It appears to be some kind of addon hydraulic valve.
  14. M

    New Steering wheel for MF 65

    I installed a new steering wheel from this site on my MF 65. I had to trim some off the bottom to clear the throttle, but that was pretty simple. The only difficult part is removing the old one, heat and persistence prevailed.
  15. M

    High/Low Jack

    My sons showed up yesterday and we kind of celebrated mother's day without her, first one. One had a black eye and stiches above it he had lost a battle with a High/Low jack handle. At the silo company we called them widow makers.
  16. M

    Loader Advice

    I recently acquired a MF 202 Work Bull. It came with a new Bucket that is somewhat over sized. I would like to install hay spears. The current loader has a loader arm spacing of about 32 inches on center. I would like to install some kind of quick attachment system. I was looking at a Titan hay...
  17. M

    1965 JD 4020

    I need to know the size of the bolts that hold the steering arm to the steering post. Dont ask. Thanks
  18. M

    Brake Story

    I stopped at a friends and he had his girl friends car on his hoist doing a brake job, 2014 Ford Fiesta. The pads were actual toast. We went to the parts store and got new pads but they didn't have the stainless steel inserts. When we went to install the pads they wouldn't go in. After...
  19. M

    Not the man I used to be

    I had to put a set of front weights on my gas 4020. With the ice on the farm drive the truck wont climb the hill with a load of round bales on the trailer. When i hooked the trailer on the three point, the front got light going up the driveway. I think they look better with the weights. I also...
  20. M

    Another Electric Puzzle

    The capacitor on the motor on my small auger went out (tab corroded off). I needed to grind feed so I hand started the 120 volt single phase motor. The motor started and the auger ran perfect, but no corn would come out of the auger. What's wrong.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top